no image yet
Ensoniq · Effect Processor

Ensoniq DP/Pro

The Ensoniq DP/Pro is a professional 24-bit effects processor built around two of Ensoniq's second-generation ESP2 signal processing chips, called ESP-A and ESP-B. Each chip runs one of 42 algorithms, each with its own variations, and the two can be routed and mixed with feedback from one to the other. The unit holds up to 387 effects in four banks: two RAM banks for the user and two ROM banks of factory effects. Analog audio enters on combination XLR and quarter-inch jacks and leaves on XLR and quarter-inch outputs, at 44.1 or 48 kHz. An optional DI-Pro board adds AES/EBU and S/PDIF digital inputs and outputs. Effects respond to Program Change and Bank Select, any MIDI controller can modulate parameters, and delays and LFOs can follow MIDI clock. The DP/Pro sends and receives System Exclusive dumps: from the System/MIDI pages it transmits the selected effect, either RAM bank, all RAM effects or all system parameters. Every dump carries the unit's MIDI Device ID, which must match when the data is loaded back.

SysEx messages

0 files

This instrument is still waiting for its first SysEx.

If you own one, or can recover a dump from an old disk or backup, upload it here: every message helps the library and the community grow.

Upload a SysEx

SysEx guide

Manufacturer ID
0F
Default device ID
MIDI Device ID 0 (range 0-127, System/MIDI parameter 6)

Receiving a dump

1. Press System/MIDI and use Next/Previous Page. 2. Set Accept MIDI Msgs=Yes. 3. Set Accept SysEx Msgs=Yes (default Yes). 4. Set the MIDI Device ID to the value stored in the dump.

Sending a dump from the instrument

1. Press System/MIDI and page to parameter 19, ENTER to Send SysEx Dump. 2. With the Value knob choose Selected Effect, Bank 0 RAM Effects, Bank 1 RAM Effects, All RAM Effects or All System Params. 3. Press Enter.

Requesting a dump

Not described in the manual; it refers to the separate DP/Pro MIDI System Exclusive Specification, once sent free on written request.

SysEx pitfalls

Dumps record the sender's MIDI Device ID; the receiving DP/Pro must have the same Device ID or it will not reload the data.

Source: Ensoniq DP/Pro Reference Manual v1.10, chapter 2 (System/MIDI parameters 6, 10, 11, 19) and chapter 12 (MIDI implementation)

Specifications

Synthesis
Dual 24-bit ESP2 effects processor, 42 algorithms with variations
Multitimbrality
Two independent effect processors (ESP-A, ESP-B), each with its own MIDI channel
Memory
Up to 387 effects: banks 0 and 1 RAM, banks 2 and 3 ROM
Keyboard / format
Rack-mount unit
Outputs
Stereo analog XLR and 1/4 inch outputs; AES/EBU and S/PDIF with optional DI-Pro board
MIDI
In, Out, Thru

Known issues and maintenance

Effects and settings are kept by an internal battery; Main battery is low at power-up means it must be replaced by an authorised service centre.

Sources

to be verified

These notes have not been checked against the sources yet. Corrections are welcome in the comments.

  1. Ensoniq DP/Pro Reference Manual, Version 1.10, 1997 (third-party copy on archive.org, catalogued as DP/2 User's guide) — Architecture, algorithms, effect banks, connections, sample rates, battery, System/MIDI parameters including Device ID and SysEx dump, MIDI implementation chart

Comments

0

Sign in to write a comment.

An unhandled error has occurred. Reload 🗙

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.