Ensoniq KT-88
The Ensoniq KT-88 is a 88-note weighted-action keyboard synthesizer from the KT series, documented together with the KT-76 in one Ensoniq manual. It plays 64 voices from a wave ROM that includes two sampled pianos, multi-sampled and synthetic waves and Ensoniq TransWaves. Each sound layers up to three voices with two filters and three envelopes, and 13 effect algorithms are built in. It holds 80 RAM sounds, 80 ROM sounds and a General MIDI set, has a 16-track sequencer and receives on up to eight channels in MULTI mode. Standard PCMCIA SRAM cards store two more banks of sounds and of sequences, and sequences can play straight from the card. The SoundFinder feature lists sounds by musical category, and the manual presents the instrument as a performance keyboard and a master controller. Over System Exclusive the KT sends the current sound or the whole internal bank of 80 sounds, and the current sequence or song or a whole bank of 70 sequences and 30 songs. Another KT or a SysEx recorder can store them; on reception a sound bank always replaces the internal bank, while a single sound arrives in the edit buffer and must be saved.
SysEx messages
0 filesThis instrument is still waiting for its first SysEx.
If you own one, or can recover a dump from an old disk or backup, upload it here: every message helps the library and the community grow.
Upload a SysExSysEx guide
- Manufacturer ID
- 0F
- Default device ID
- ID parameter 01 to 16 on System-MIDI page 8 (factory default not stated)
Receiving a dump
1. Press SYSTEM-MIDI. 2. Press the lower 8 button. 3. Set SysEx=ON with the Data Entry controls. Reception then starts automatically when a dump arrives.
Sending a dump from the instrument
Sounds: 1. Press EDIT SOUND, then the upper 9 button (Press ENTER to Store Sound Data). 2. Press ENTER and select Storage Type=MIDI SYS-EX. 3. Press ENTER, choose SAVE CURRENT SOUND or SAVE i:INT SOUND BANK. 4. Press ENTER. Sequencer: same steps from EDIT SEQ/PRESET, choosing SAVE CURRENT SEQ/PSET or SAVE CURRENT SEQ BANK.
Requesting a dump
The manual describes no dump request; it refers to the separate KT System Exclusive Specification, once available on written request from Ensoniq.
SysEx pitfalls
A received sound bank always overwrites the 80 internal RAM sounds. A single sound goes to the edit buffer and must be saved. A sequencer bank goes to the current seq bank and is ignored if that is ROM. In General MIDI mode all SysEx except GM Off is ignored.
Source: Ensoniq KT Musician's Manual v1.5, Section 2 p. 17 and Section 13 pp. 5-8 ↗
Specifications
- Synthesis
- Sample-based synthesis with wave ROM, multi-sampled waves and TransWaves; 13 effect algorithms
- Polyphony
- 64 voices (up to three voices per key in a Standard Sound)
- Multitimbrality
- Up to 8 MIDI channels in MULTI mode; 16 channels in General MIDI mode
- Oscillators
- Up to three layered voices per Standard Sound
- Filter
- Two filters per voice sharing four poles: 2- or 3-pole low pass, then 1- or 2-pole high or low pass
- Memory
- 80 RAM and 80 ROM sounds plus drum and GM sounds; 70 sequences and 30 songs; PCMCIA SRAM card adds 160 sounds
- Keyboard / format
- 88 notes, weighted action, velocity and channel pressure
- Outputs
- Left/Mono and Right/Mono line outputs, stereo headphone jack
- MIDI
- In, Out, Thru
Known issues and maintenance
Internal RAM is kept by a battery rated for up to five years; Main Battery Low at power-up means it must be replaced by a service centre. Card Battery Low refers to the battery in the PCMCIA RAM card.
Sources
to be verifiedThese notes have not been checked against the sources yet. Corrections are welcome in the comments.
- Ensoniq KT Musician's Manual, Version 1.5, 1994-1995, covering KT-76 and KT-88 (third-party copy) ↗ — Introduction, polyphony, sound memory, filters, MIDI modes, System-MIDI page 8 SysEx and ID, Section 13 Storage (MIDI Sys-Ex dumps), MIDI implementation chart, battery
Sign in to write a comment.
Comments
0