no image yet
Eventide · Effect Processor

Eventide DSP4000

The Eventide DSP4000 is a member of the 4000 Series Ultra-Harmonizer family, a line of programmable digital signal processors with pitch change at their core. Eventide sold several versions tailored to different markets, including the DSP4000B, DSP4500 and GTR4000, and most features of one were available as options on the others. The unit ships with hundreds of factory programs and has a built-in patch editor in which users assemble their own effects from modules. The DSP4000 has two audio channels on balanced XLR and 1/4-inch jacks, S/PDIF and AES/EBU digital I/O as standard, MIDI In, Out and Thru, a pedal input, a two-way footswitch input and a relay output. Options included a sampler card and preset cards. The unit sends and receives Eventide system exclusive messages. Its MIDI data dumps page can send the current program, the setup, all user setups and programs in internal memory, the memory card contents, or the whole internal memory. A receiving 4000 with the same device ID loads the data automatically, and parameter changes can also be recorded to a sequencer as SysEx.

SysEx messages

0 files

This instrument is still waiting for its first SysEx.

If you own one, or can recover a dump from an old disk or backup, upload it here: every message helps the library and the community grow.

Upload a SysEx

SysEx guide

Manufacturer ID
1C
Default device ID
Device ID 1 (factory default); range 1-99; messages with ID 0 are accepted by any unit

Receiving a dump

1. Press SETUP and the [midi] soft key. 2. Set MIDI to enabled and system exclusive to on. 3. For program dumps set program load to on. 4. Set device ID to match the sending unit, then send the data to MIDI In.

Sending a dump from the instrument

1. Press SETUP and go to the [dump] soft key (MIDI data dumps). 2. Light the box for dump program, dump setup, dump files, dump card or dump internal. 3. Press SELECT; a running count of MIDI bytes is shown.

SysEx pitfalls

Dumps are sent regardless of the MIDI settings but carry the device ID. On receipt, dump setup restarts the unit with the new setup; dump files erases all saved setups and programs (factory programs are not included); dump card is ignored if the receiver has no card or too small a card; dump internal replaces everything and restarts the unit.

Source: Eventide 4000 Series Ultra-Harmonizer Operator's Manual, rev 2.0, release 7, pp. 5, 25, 75-77 ↗

Specifications

Memory
Factory programs plus user setups and programs in internal memory; optional memory card
Keyboard / format
Rack unit
Outputs
2 channels on balanced XLR and 1/4-inch jacks; S/PDIF and AES/EBU digital outputs (standard on the DSP4000)
MIDI
MIDI In, MIDI Out, MIDI Thru; RS-422 in/out

Sources

to be verified

These notes have not been checked against the sources yet. Corrections are welcome in the comments.

  1. Eventide 4000 Series Ultra-Harmonizer Operator's Manual (DSP4000 and GTR4000), software rev 2.0, document release 7, 1992-1995; scanned PDF read as page images ↗ — Introduction p. 1, rear panel pp. 4-5, MIDI data dumps p. 25, MIDI chapter pp. 74-77
  2. Eventide DSP4000 product page ↗ — Description, model list (DSP4000, DSP4000B, DSP4500, GTR4000), manual link

Comments

0

Sign in to write a comment.

An unhandled error has occurred. Reload 🗙

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.