no image yet
Eventide · Effect Processor · 2001

Eventide Eclipse

The Eventide Eclipse is a single-rackspace stereo effects processor introduced around 2001. Its two effects blocks can run in series, in parallel or as dual mono, and draw on roughly a hundred algorithms covering pitch shifting, reverbs, delays, modulation and more, which Eventide presents as an inheritance from its Orville and H3000 processors. A later V4 software release kept the same hardware. The unit stores 100 user programs internally and 500 more on a memory card, runs at sample rates up to 96 kHz and has balanced analog, AES, S/PDIF, optical and ADAT connections, word clock, a 7-pin MIDI input that can power a pedal board, and an RS-232 serial port. Sound On Sound reviewed it in September 2001 and described its MIDI implementation as comprehensive. The Eclipse sends and receives Eventide system exclusive messages. From the Setup area it can dump the program currently running, all programs held in internal memory, or the system setup (the saved Setup and Levels values) out of the MIDI and serial ports. Sending a dump back with a matching Device ID loads the program or replaces the stored data.

SysEx messages

0 files

This instrument is still waiting for its first SysEx.

If you own one, or can recover a dump from an old disk or backup, upload it here: every message helps the library and the community grow.

Upload a SysEx

SysEx guide

Manufacturer ID
1C
Default device ID
Device ID 1 (factory default); range 1-127, Off disables SysEx

Receiving a dump

1. Go to SETUP page 2 MIDI SYSEX and set (SYS EXC) to the Device ID used when the data was sent. 2. Make sure the MIDI channel is not set to Off. 3. Send the dump to MIDI In (or the serial port); the Eclipse loads it automatically.

Sending a dump from the instrument

1. Go to SETUP page 3 DUMP. 2. With (DATATYPE) choose Current Prog, Internal Progs or System Setup. 3. Press <DUMP>; a running byte count is shown while the data goes out MIDI Out and the serial port.

SysEx pitfalls

Receiving Internal Progs erases internal memory and replaces it; System Setup replaces the Setup and Levels values. A corrupted dump sent back can lose both the backup and the unit's contents, so the manual advises recording twice and comparing file sizes. SYSXSPD (1-10) slows transmission for slow receivers. Do not loop SEQ OUT back into the unit.

Source: Eventide Eclipse User Manual, part 141045, release 4.0.2, pp. 10, 48-52 ↗

Specifications

Memory
100 user programs in internal memory (0-99), 500 on a memory card (500-999); factory programs 100-499
Keyboard / format
1U rack unit (1.75 x 19 x 12.5 in)
Outputs
Balanced XLR and unbalanced 1/4-inch outputs; AES, S/PDIF coaxial and optical, ADAT; word clock
MIDI
MIDI In (7-pin, can power a pedal board), MIDI Out, MIDI Thru; RS-232 serial port

Known issues and maintenance

Internal memory is kept by a long-life battery; a checksum error at power-up warns of possible memory corruption. A frozen unit can be started with the MUTE program by holding PROGRAM at power-up.

Sources

to be verified

These notes have not been checked against the sources yet. Corrections are welcome in the comments.

  1. Eventide Eclipse User Manual, part no. 141045, Manual/Software Release 4.0.2 (2018) ↗ — MIDI ports p. 10, Device ID and SYSXSPD pp. 48-49, dumps pp. 51-52, battery and checksum p. 53, electrical specifications pp. 58-59
  2. Eventide Eclipse V4 product page ↗ — Description, almost 100 algorithms, specifications, link to the manual
  3. Hugh Robjohns, Eventide Eclipse, Sound On Sound, September 2001 ↗ — Review: 1U format, program memory layout, SysEx dumps, MIDI implementation

Comments

0

Sign in to write a comment.

An unhandled error has occurred. Reload 🗙

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.