no image yet
Eventide · Effect Processor

Eventide H8000

The Eventide H8000 is a two-rackspace multichannel effects processor built around two independent DSPs. Each DSP has eight virtual inputs and outputs, the two can be chained in series or parallel, and large monolithic programs can use both at once. Its library covers reverbs, pitch shifting, delays, dynamics, EQ, filters, synthesis and sampling, and users can build their own programs from modules, a method Eventide carried over from the DSP4000. The original H8000 has two analog channels plus eight AES/EBU and eight ADAT channels; the later H8000A and H8000FW changed the I/O mix, the FW adding FireWire. The unit runs at up to 96 kHz, stores data on a PCMCIA memory card and offers long sampling and delay times. Eventide documents the whole family in the H8000FW manual, which says most of it applies to the H8000 running software 5.2 or later. The H8000 sends and receives Eventide system exclusive messages. The dump page in the Setup area can send the program on the displayed DSP, the setup, all user setups, programs and routings in internal memory, the memory card contents, or the complete internal memory. Sending the data back with the same device ID restores it.

SysEx messages

0 files

This instrument is still waiting for its first SysEx.

If you own one, or can recover a dump from an old disk or backup, upload it here: every message helps the library and the community grow.

Upload a SysEx

SysEx guide

Manufacturer ID
1C
Default device ID
Device ID 1 (factory default)

Receiving a dump

1. Press SETUP and open the midi menu page. 2. Set MIDI to enabled and system exclusive to on. 3. Set device ID to the value used when the data was sent. 4. Send the dump to MIDI In or the serial port.

Sending a dump from the instrument

1. Press SETUP and open the dump menu page. 2. Highlight dump program, dump setup, dump files, dump card or dump internal. 3. Press SELECT; the data goes out MIDI Out and the serial port with a running byte count.

SysEx pitfalls

dump files does not include factory presets; receiving it erases all saved setups and programs. dump card is ignored if no card or too small a card is fitted. dump internal also loads both running programs and restarts the unit. A corrupted dump sent back can destroy both backup and unit contents; record twice and compare. sysex speed lowers the transmit rate for slow receivers.

Source: Eventide H8000FW Operating Manual, software 5.5, release 1.6 (2010), pp. 93-95 and 140-143 ↗

Specifications

Memory
User programs, setups and routings in internal memory plus PCMCIA memory card; factory presets in ROM
Keyboard / format
2U rack unit (3.5 x 19 x 12.5 in)
Outputs
H8000: 2 analog channels, 8 AES/EBU channels, 8 ADAT channels
MIDI
MIDI In (7-pin, with output capability), MIDI Out, MIDI Thru; serial port

Known issues and maintenance

Internal memory is kept by a lithium button battery rated for about five years; Eventide says it must be replaced by a technician with the unit powered on so the memory is preserved.

Sources

to be verified

These notes have not been checked against the sources yet. Corrections are welcome in the comments.

  1. Eventide H8000FW Operating Manual, software version 5.5, part 141103, release 1.6 (2 March 2010) ↗ — Applies to H8000/H8000A with software 5.2+; architecture pp. 3-4, I/O per model p. 53, MIDI pp. 93-95, dumps pp. 140-141, battery p. 149, specifications pp. 191-192
  2. Eventide H8000 product page ↗ — Describes the H8000FW: presets, specifications, link to the manual

Comments

0

Sign in to write a comment.

An unhandled error has occurred. Reload 🗙

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.