no image yet
Korg · Effect Processor

Korg A3

The Korg A3 Performance Signal Processor is a 19-inch rack multi-effect unit whose manual dates from 1988. It offers 41 digital effect types arranged in 20 preset chains, each using up to six effects at once, from compressor, distortion and exciter through delays, modulation, pitch shifting and rotary speaker simulation to reverb and early reflections. Edited settings are stored in 100 program memories, or 200 with a card. Conversion is 16-bit at 37.1 kHz with a 4x oversampling digital filter, and a digital noise reduction cuts hum and noise between notes. ROM cards can load new effects, chains and programs into the unit, a RAM card holds user programs, and the optional FC6 foot controller switches programs and individual effects on stage. Over MIDI the A3 receives program changes and saves or loads its entire memory as one System Exclusive message, the All Data dump of programs and chains, about 29 KB long. The dump is started from the MIDI page of Utility mode and is received in the same page with the Load function, replacing programs 1 to 100. There is no single-program dump.

SysEx messages

0 files

This instrument is still waiting for its first SysEx.

If you own one, or can recover a dump from an old disk or backup, upload it here: every message helps the library and the community grow.

Upload a SysEx

SysEx guide

Manufacturer ID
42
Model ID
20
Default device ID
MIDI channel 1 (range 1-16)

Receiving a dump

1. Connect the MIDI OUT of the sending device to the A3 MIDI IN. 2. In Utility mode open the MIDI page and press double function editor D (LOAD). The display shows LOADING. 3. Send the data: the load runs automatically and the display shows LOAD COMPLETED. The data goes to programs 1-100.

Sending a dump from the instrument

1. Set the MIDI OUT/THRU switch on the rear panel to OUT. 2. Connect the A3 MIDI OUT to the MIDI IN of the receiving device and set the receiver to record or receive. 3. In Utility mode open the MIDI page and press double function editor E (SAVE). The display shows SAVING. and returns to the MIDI page when the dump is complete.

SysEx pitfalls

The All Data (Program and Chain) dump is one message with 29192 data bytes ((6400 + 8192 + 4) x 2). Its header is printed as F0 42 21 20, while the Bank Change message uses F0 42 3n 20. If DATA ERROR!! appears the transfer failed; if LOADING stays on the display, no data or non-A3 data arrived, and erroneous data may overwrite some programs. No single-program dump and no dump request are documented.

Source: Korg A3 Owner's Manual (scan), Utility MIDI pp. 39-41, MIDI Implementation p. 46, MIDI Implementation Chart p. 49 ↗

Specifications

Memory
100 programs (200 with a card); 20 preset effect chains of up to 6 effects, 41 effect types
Keyboard / format
19-inch rack unit, 44 mm high
Outputs
Output L and R, Direct Out, Phones (stereo)
MIDI
MIDI IN, MIDI OUT/THRU (switchable)

Known issues and maintenance

An internal backup battery preserves the programs; at power-on the message INTERNAL BACKUP BATTERY LOW! asks for replacement by a dealer or service center. RAM cards use a CR2016 lithium battery, to be replaced with the card inserted in the A3.

Sources

to be verified

These notes have not been checked against the sources yet. Corrections are welcome in the comments.

  1. Korg A3 Performance Signal Processor Owner's Manual (English, scanned PDF read as page images) ↗ — Main features p. 2, Utility MIDI pp. 39-41, battery messages p. 41, MIDI implementation p. 46, specifications p. 48, MIDI chart p. 49, copyright 1988
  2. Korg A3, Music Technology, July 1989 (Vic Lennard) ↗ — Contemporary review: UK price, no single-patch dump, no MIDI parameter control, verdict

Comments

0

Sign in to write a comment.

An unhandled error has occurred. Reload 🗙

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.