no image yet
Korg · Synthesizer · 2003

Korg Electribe EMX-1

The Korg Electribe EMX-1 (Electribe MX) is a tabletop music production station from 2003 that combines a drum machine, a synthesizer and a step sequencer. It has nine drum parts, built on 207 PCM drum waves, and five synth parts based on Korg's Multi Modeling Technology, with sixteen oscillator types that range from classic analogue models to chord, unison and waveshape types. Each synth part is monophonic. Three effect processors, an audio input that can be run through the filter and effects, and the VALVE FORCE circuit with two real 12AX7 valves on the output complete the design. Patterns of up to 128 steps per part are kept in 256 memories, 192 of them programmed at the factory, and 64 songs chain the patterns together with knob movements. Data can also be saved on SmartMedia cards. Sound On Sound (November 2003) found it easy to use with a great sound, but regretted the mono audio input and the very basic envelopes. The EMX-1 has no separate sound memories: sounds are stored inside the patterns. Its System Exclusive dumps carry a bank of 64 patterns, all songs or the global settings, and are sent from the MIDI dump page or on request. Memory protect is on when the unit leaves the factory and must be turned off before a dump can be received.

Sign in to upload or comment

SysEx messages

0 files

This instrument is still waiting for its first SysEx.

If you own one, or can recover a dump from an old disk or backup, upload it here: every message helps the library and the community grow.

Upload a SysEx

SysEx guide

Manufacturer ID
42
Model ID
69
Default device ID
Global MIDI channel, which is the channel of synth part 1 (factory setting 1)

Receiving a dump

1. Press GLOBAL, select Protect and set it to Off (it is On at the factory). 2. Set the MIDI channel of synth part 1 (MIDI mode, MIDI ch) to the channel used when the dump was saved. 3. Press the MIDI key, hold SHIFT and press step key 12 (MIDI UTILITY). 4. Turn the dial to Dump and press key 12: the display shows MIDIDump. 5. Send the file from the computer. Do not touch the keys; the EMX-1 needs up to ten seconds to write each dump into memory.

Sending a dump from the instrument

1. Press the MIDI key, hold SHIFT and press step key 12 (MIDI UTILITY). 2. Turn the dial to Dump and press key 12: the display shows MIDIDump. 3. Turn the dial to choose PtBnkA, PtBnkB, PtBnkC, PtBnkD (64 patterns each), AllSng (all songs) or Global. 4. Press key 12 again to transmit. STOP/CANCEL cancels before transmission starts.

Requesting a dump

Requests, with g = global MIDI channel minus 1: Current pattern: F0 42 3g 69 10 F7 (answer 40). Pattern bank: F0 42 3g 69 1C bb F7, bb 0-3 = bank A-D (answer 4C). Current song: F0 42 3g 69 0A F7 (answer 58). All songs: F0 42 3g 69 0B F7 (answer 57). Global: F0 42 3g 69 0E F7 (answer 51).

SysEx pitfalls

Dumps are received only when the sequencer is stopped or on the MIDI dump page, and with Protect On only in Global mode. After each received dump the unit answers 23 (Data Load Completed) or 24 (Data Load Error) and takes up to ten seconds to write; leave a pause between dumps. Data is 8-bit and packed 7-to-8 for MIDI; one pattern is 4,806 bytes before packing and the global data 192 bytes.

Source: Korg EMX-1 Owner's Manual pp. 75, 79, 82, 85; EMX-1 MIDI Implementation v1.2 (2006) ↗

Specifications

Synthesis
MMT modelling synth parts (16 oscillator types) plus PCM drum parts (207 drum waves)
Polyphony
Each of the 5 synth parts is monophonic
Multitimbrality
16 parts: 5 synth, 9 drum, 1 synth accent, 1 drum accent
Oscillators
1 oscillator per synth part with 16 types; 1 of 207 PCM waves per drum part
Filter
Synth parts: low-pass, high-pass, band-pass and BPF+ with drive
Memory
256 patterns (192 factory), 64 songs; SmartMedia card slot
Keyboard / format
Tabletop unit with 16 step keys, ribbon controller and arpeggiator slider
Outputs
L/MONO and R, individual outputs 3 and 4, headphones; mono audio input
MIDI
MIDI In, Out, Thru

Known issues and maintenance

Memory protect is on at the factory: patterns and songs cannot be written and dumps cannot be received until Protect is set to Off in Global mode. The two vacuum tubes are not user serviceable. To restore the factory patterns and songs, power on while holding Transpose (Solo) and Write and press PLAY/PAUSE: user data is erased. Korg warns that some USB-MIDI interfaces cannot pass the EMX-1's exclusive messages.

Sources

to be verified

These notes have not been checked against the sources yet. Corrections are welcome in the comments.

  1. Korg EMX-1 Owner's Manual (E1, 2003) ↗ — Features, monophonic synth parts, memory protect, MIDI channels, dump procedures, SysEx format, factory preload, specifications
  2. Korg EMX-1 MIDI Implementation, version 1.2 (25 August 2006) ↗ — Exclusive header with model ID 69, device inquiry, dump and request messages, table sizes, receive conditions
  3. Korg USA: ELECTRIBE-MX downloads ↗ — List of manuals and MIDI implementation; product marked sold out
  4. Derek Johnson, "Korg Electribe EMX1", Sound On Sound, November 2003 ↗ — Review: price, 207 PCM drum waveforms, filter types, MIDI dump backup, pros and cons

Comments

0

Sign in to write a comment.

An unhandled error has occurred. Reload 🗙

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.