no image yet
Korg · Synthesizer

Korg R3

The Korg R3 is a 37-key synthesizer and vocoder built on MMT (Multiple Modeling Technology), the same architecture as Korg's larger RADIAS. A program can use up to two timbres, layered or split, with 8-voice polyphony. Each timbre has two oscillators plus noise, where the first offers modelled analogue waves, formant, DWGS digital waves, the audio input and VPM, cross and unison modulation, followed by a wave shaper, two filters with a comb option, three envelopes, two LFOs and a virtual patch matrix. A 16-channel vocoder with a supplied gooseneck microphone can store 16 formant motion recordings. Sound On Sound (September 2007) called the R3 a little synth with a big heart and thought the vocoder alone might justify the purchase, while noting small displays, no aftertouch and only 128 program memories. The R3 holds 128 programs in 16 banks of 8. From the SHIFT menu it sends System Exclusive dumps of one program, all programs, the global data (which includes the formant motion recordings) or everything, through MIDI or USB, and it can answer dump requests from the Sound Editor or another computer program. A single program is 452 bytes; a full AllData dump is about 250,000 bytes and takes around five and a half minutes over MIDI.

SysEx messages

0 files

This instrument is still waiting for its first SysEx.

If you own one, or can recover a dump from an old disk or backup, upload it here: every message helps the library and the community grow.

Upload a SysEx

SysEx guide

Manufacturer ID
42
Model ID
7D
Default device ID
Global MIDI channel (page 42 MIDI, MIDI Ch 1-16), as 3g in the header

Receiving a dump

1. Connect the R3 MIDI IN to the sender's MIDI OUT (or use USB). 2. Set the sender to the R3's global MIDI channel; for a dump made earlier, set the R3 to the channel used when it was sent. 3. On page 43 MIDI FILTER set SystemEx to Enable. 4. Turn the SHIFT function PROTECT off (SHIFT + 8, PAGE dial). 5. Send the data. A single program dump (function 4C) is saved into internal memory; a current program dump (40) goes into the edit buffer.

Sending a dump from the instrument

1. Connect the R3 MIDI OUT to the receiver and set both to the same MIDI channel. 2. Hold SHIFT and press PROGRAM SELECT 6; the 6 button blinks. 3. Turn the PAGE dial to choose 1 Prog, AllProg, Global or AllData. 4. Press the blinking 6 button. The R3 returns to Play mode when the dump is done.

Requesting a dump

Current program: F0 42 3g 7D 10 F7 (answer: function 40). One program: F0 42 3g 7D 1C pp 0p F7, program number split into low 7 bits and high bits (answer: 4C). Global data: F0 42 3g 7D 0E F7 (answer: 51). Formant motion: functions 13 (current) and 18. g is the global MIDI channel minus 1. The unit answers 24 (Data Load Error) when it cannot comply.

SysEx pitfalls

Program data is 452 bytes packed into 517 MIDI bytes; global data is 256 bytes packed into 293. The manual table gives 452 bytes for 1 Prog, 57,856 for AllProg (about 3 min 15 s), 192,144 for Global (about 2 min 10 s, formant motion included) and 250,000 for AllData (about 5 min 30 s). After each received block the R3 sends 23 or 24; a malformed message gets 26.

Source: Korg R3 Owner's Manual pp. 69, 70, 77-78; R3 MIDI Implementation; R3 MIDI Implementation Chart (2006.8.2) ↗

Specifications

Synthesis
MMT (Multiple Modeling Technology) virtual analogue with 16-channel vocoder
Polyphony
8 voices
Multitimbrality
2 timbres per program (Layer, Split, Multi)
Oscillators
2 oscillators + noise per timbre; OSC1 8 types (saw, pulse, triangle, sine, formant, noise, DWGS, audio in), OSC2 4 types with ring and sync
Filter
Filter 1: -24 dB/oct LPF, -12 dB/oct LPF, BPF, HPF, Thru; Filter 2: LPF, HPF, BPF, comb
Memory
128 programs (16 banks x 8), 16 formant motion data sets
Keyboard / format
37 full-size keys, velocity sensitive, no aftertouch
Outputs
L/MONO and R (1/4 inch), headphones; XLR mic input and two 1/4 inch audio inputs
MIDI
MIDI In, Out, Thru; USB B (MIDI)

Known issues and maintenance

Write Protect (SHIFT + 8) must be turned off before programs can be saved or dumps received. Korg warns that some USB-MIDI interfaces may not pass the R3's exclusive messages. The knobs and buttons must not be touched while a dump is being sent or received.

Sources

to be verified

These notes have not been checked against the sources yet. Corrections are welcome in the comments.

  1. Korg R3 Owner's Manual ↗ — MIDI Data Dump procedure and size table p.77, Preload and Write Protect p.78, MIDI and MIDI Filter pages pp.69-70, specifications p.87
  2. Korg R3 MIDI Implementation ↗ — Header with model ID 7D, device inquiry, function IDs, dump and request formats, data sizes
  3. Korg R3 MIDI Implementation Chart (2006.8.2) ↗ — System Exclusive transmitted and recognised, controlled by the MIDI Filter SystemEx setting
  4. Korg USA support downloads: R3 ↗ — Manuals, MIDI implementation, Sound Editor, R3 Bonus Program and Power Bank
  5. Paul Nagle, "Korg R3 Synth/Vocoder", Sound On Sound, September 2007 ↗ — Review: price, relation to the RADIAS, vocoder, criticisms

Comments

0

Sign in to write a comment.

An unhandled error has occurred. Reload 🗙

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.