no image yet
Oberheim · Sound Module · 1986

Oberheim Matrix-6R

The Oberheim Matrix-6R is the rack-mounted version of the Matrix-6 keyboard, released in 1986 and sold in the UK for 949 pounds. Oberheim describes it as built on the same technology as the Matrix-6 in a lower-cost rack unit. It is a six-voice analogue synthesizer: each voice has two digitally controlled oscillators, a four-pole low-pass filter, three envelopes and two LFOs. Its best-known feature is Matrix Modulation, a patch bay in software that lets up to 20 sources modulate up to 32 destinations, with ten free routings per patch on top of the fixed ones. It stores 100 patches and 50 splits, and adds MIDI functions such as patch mapping and a MIDI Mono mode for sequencer tracks or guitar controllers. Patches can also be saved to cassette. The Matrix-6R sends and receives patch data as System Exclusive once its SYSTEM EXCLUSIVE parameter is switched on. From the Master page it can send the current patch or everything at once: master settings, splits and all 100 patches. The manual names another Matrix-6R, a Matrix-6 or a computer with suitable software as receivers.

Sign in to upload or comment

SysEx messages

0 files

This instrument is still waiting for its first SysEx.

If you own one, or can recover a dump from an old disk or backup, upload it here: every message helps the library and the community grow.

Upload a SysEx

SysEx guide

Manufacturer ID
10

Receiving a dump

1. On the Master page set parameter 04 SYSTEM EXCLUSIVE to ON. 2. Set the Memory Protect switch on the back panel to OFF; when it is on, incoming MIDI data is refused. 3. For a single patch, select the patch number where it should be stored.

Sending a dump from the instrument

1. Connect MIDI Out of the sending unit to MIDI In of the receiver. 2. For a single patch, select the patch to send. 3. Set Master parameter 04 SYSTEM EXCLUSIVE to ON on both instruments. 4. Select Master parameter 10 SEND PATCH (current patch) or 11 SEND ALL (master settings, splits and all 100 patches). 5. Press VALUE: the display shows READY?. 6. Press YES. When the transfer ends the display returns to the SEND message.

SysEx pitfalls

System Exclusive must be on in both units, and Memory Protect must be off on the receiver. The manual names another Matrix-6R, a Matrix-6 or a computer with Oberheim System Exclusive software as receivers.

Source: Oberheim Matrix-6R Owner's Manual (1986), Master parameters 04, 10 and 11, pp. 62-65

Specifications

Synthesis
Analogue subtractive with digitally controlled oscillators and Matrix Modulation
Polyphony
6 voices
Multitimbrality
Splits combine two patches
Oscillators
2 DCOs per voice
Filter
4-pole (24 dB/octave) low-pass per voice
Memory
100 patches and 50 splits
Keyboard / format
Rack module, no keyboard
Outputs
Left/Mono and Right audio outputs
MIDI
In, Out, Thru

Known issues and maintenance

Memory Protect switch on the back panel: when it is on, nothing can be stored, cassette loads are refused and incoming MIDI data is blocked (the display shows MEMORY PROTECTED). Single patches can also be protected individually.

Sources

to be verified

These notes have not been checked against the sources yet. Corrections are welcome in the comments.

  1. Oberheim, Matrix-6R Owner's Manual, 1986 (third-party copy on ManualsLib) — Architecture, memory, connections, Memory Protect, System Exclusive parameter and patch transfer procedure. Third-party copy of the manufacturer document
  2. Simon Trask, Oberheim Matrix 6R Expander, Electronics & Music Maker, July 1986 ↗ — Rack version of the Matrix-6, Matrix Modulation, 100 patches and 50 multipatches, price

Comments

0

Sign in to write a comment.

An unhandled error has occurred. Reload 🗙

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.