Roland GP-8
The Roland GP-8 is a rack-mounted guitar effects processor introduced in 1987. It puts eight effects in one unit, always in the same order: dynamic filter (an automatic wah), compressor, Turbo Overdrive, distortion, phaser, three-band equalizer, digital delay of up to one second and digital chorus. A send and return loop sits between the equalizer and the delay, and two switching outputs can turn external effect units on and off from each patch. There are no knobs for the individual effects: parameters are called up on a two-line display and set with the Alpha Dial. The GP-8 stores 128 named patches in two groups of eight banks, selected from the panel, by MIDI program change or with the optional FC-100 foot controller, and one parameter per patch can be assigned to an EV-5 expression pedal. Reviewing it in 1987, Making Music praised the design and the usable factory patches but found the price high. Over MIDI the GP-8 sends and receives its patches as Roland System Exclusive data. A bulk dump started from the front panel contains either the current patch or all 128 patches, names included, and a dump that arrives is loaded automatically, replacing what was in memory. Roland's manual lists the complete data format and the factory values of every patch.
Sign in to upload or commentSysEx messages
0 filesThis instrument is still waiting for its first SysEx.
If you own one, or can recover a dump from an old disk or backup, upload it here: every message helps the library and the community grow.
Upload a SysExSysEx guide
- Manufacturer ID
- 41
- Model ID
- 13
- Default device ID
- MIDI basic channel, 1-16 (device ID byte = channel minus 1)
- Suggested delay between messages
- 20 ms
Receiving a dump
1. Set the Selector Switch on the rear panel to MIDI IN (the FC-100 foot controller cannot be used at the same time). 2. Press MIDI: the display shows MIDI CHANNEL. Set the channel to the one used in the data: the device ID of the messages is the MIDI channel. 3. Send the data. There is nothing to enable: the GP-8 loads it automatically and the patch display shows Ld.
Sending a dump from the instrument
1. Connect MIDI OUT to the MIDI IN of the receiver and set the GP-8 to the receiver's MIDI channel. 2. Press MIDI and turn the Alpha Dial until the display shows BULK DUMP, OFF. 3. Press VALUE: OFF flashes. Turn the Alpha Dial to CURRENT (the selected patch) or ALL (all 128 patches). 4. Press MIDI to enter the choice. 5. Press WRITE: the display shows SAVING while the data is sent.
Requesting a dump
The GP-8 recognizes a Roland one-way data request (RQ1): F0 41, the device ID, 13 11, a 2-byte address, a 2-byte size, the checksum and F7. It answers with data set (DT1) messages. Address 00 00 is the temporary patch; the stored patches start at 20 00 and follow every 40 hex up to 3F C0 (patch 128). Even if the address or the size covers only part of a patch, the whole patch is sent.
SysEx pitfalls
One-way transfer, no handshake. The GP-8 leaves about 20 ms between messages and expects a wait of more than 20 ms between the messages it receives. A received dump overwrites memory without asking: a single patch replaces the patch with the same number, a full dump replaces all 128. The manual describes no memory protection. The checksum of received data is not checked, because data is written as it arrives. A dump made with ALL contains all programs and the temporary parameters.
Source: Roland GP-8 Owner's Manual (1987), pp. 25-27 and MIDI Implementation, pp. 33-35 of the PDF ↗
Specifications
- Synthesis
- Eight effects in a fixed chain: dynamic filter, compressor, Turbo Overdrive, distortion, phaser, 3-band equalizer, digital delay (0-1000 ms), digital chorus
- Memory
- 128 patches (groups A and B, 8 banks of 8 each), each with a name of up to 16 characters; battery backed
- Keyboard / format
- 19-inch rack unit, 44 mm high (482 x 282 x 44 mm, 4 kg)
- Outputs
- Output A (mono) and B, Line Out A (mono) and B, effect Send and Return, two External Control outputs; guitar input on front and rear panel
- MIDI
- MIDI In, Out, Thru; RRC In for the FC-100 foot controller (a rear switch selects RRC In or MIDI In)
Known issues and maintenance
Backup battery. The patches are kept by a lithium battery; the manual says to have it replaced every five years by Roland service. No factory reset. Roland states that the GP-8 has no reset function: the factory values of all 128 patches are printed in the PRESET SETTING tables of the owner's manual. Foot controller or MIDI In. A rear switch selects the FC-100 input (RRC In) or MIDI In; the two cannot be used at the same time. Early units. A Roland change notice for serial numbers 761000 to 783499 describes a modification of the main board to prevent a faulty chorus, wrong LED readings and an effect that stays off when switched on together with others. The unit is muted for about five seconds after power-on. Compressor, distortion and overdrive switched on together may cause noise or oscillation.
Sources
to be verifiedThese notes have not been checked against the sources yet. Corrections are welcome in the comments.
- Roland GP-8 Owner's Manual (1987) ↗ — Effects and parameters, memory, connections, battery, bulk dump and bulk load, MIDI implementation, factory patch tables, change notice for early serial numbers
- Roland Knowledge Base: GP-8: Does it have a Factory Reset, or function to reset to default factory settings? ↗ — The GP-8 has no factory reset; factory values are in the manual
- Roland support: Factory Patches (D-series, JUNO-1/2, MKS-series, U-series, GP-8, GR-50) ↗ — Roland publishes the factory patches of the GP-8 as .mid files
- Jon Lewin, "Roland GP8 multi-effects", Making Music, May 1987 ↗ — Contemporary review: fixed effect order, expression pedal, UK price, verdict
- "Frankfurt" news special, Making Music, March 1987 ↗ — The GP-8 shown as a new product in early 1987
- Gordon Reid, "The History Of Roland: Part 3", Sound On Sound, January 2005 ↗ — Lists the GP-8 among the 1987 products
Sign in to write a comment.
Comments
0