no image yet
Roland · Synthesizer · 1998

Roland JP-8080

The Roland JP-8080 is a rack-mounted virtual analogue synthesizer released in 1998. It uses the same analog modeling sound source as the JP-8000 keyboard, with two oscillators per voice, including the Super Saw wave, and a filter that works as low-pass, band-pass or high-pass. It plays 10 voices, or 8 with the Voice Modulator on, and two parts can be layered or split. Compared with the JP-8000 it adds the Voice Modulator, a vocoder with two 12-band filter banks, external audio inputs that can be processed by the filter, and more polyphony. It holds 128 user and 384 preset patches, 64 user and 192 preset performances, and stores more on SmartMedia cards. The Bulk Dump function sends user patches, performances, motions and system settings as Roland System Exclusive messages, all together or one group at a time. The manual also explains how to load JP-8000 dumps into the JP-8080.

Sign in to upload or comment

SysEx messages

0 files

This instrument is still waiting for its first SysEx.

If you own one, or can recover a dump from an old disk or backup, upload it here: every message helps the library and the community grow.

Upload a SysEx

SysEx guide

Manufacturer ID
41
Model ID
00 06
Default device ID
Device ID 17 (range 17-32); dev byte 10H
Suggested delay between messages
20 ms

Receiving a dump

1. Connect the sequencer's MIDI OUT to the JP-8080 MIDI IN (not REMOTE KBD IN). 2. Press MIDI and set Device ID to the value used when the dump was made. 3. In the MIDI settings, set Rx Exclusive SW to ON. 4. Play back the data at the same tempo used when it was recorded. The received data overwrites the internal memory.

Sending a dump from the instrument

1. Connect the JP-8080 MIDI OUT to the sequencer's MIDI IN. 2. Press EDIT. 3. Press INIT/UTIL (BANK 7) several times until the Bulk Dump display appears. 4. Use DEC/INC to choose the type: ALL, PERFORM (USER ALL or TEMP), PATCH (USER ALL, USER A, USER B, TEMP UPPER, TEMP LOWER, TEMP UP&LO), MOTION or SYSTEM SETUP. 5. Start recording on the sequencer. 6. Press WRITE. The display shows Completed when the dump ends (EXIT stops it). 7. Stop the sequencer.

Requesting a dump

Send a Roland data request RQ1: F0 41, device ID, 00 06 11, a 4-byte address, a 4-byte size, the checksum and F7. If the address and size are valid the JP-8080 answers with DT1 messages; otherwise it sends nothing.

SysEx pitfalls

Do not play the MIDI keyboard during a dump. RPS patterns cannot be dumped, and card data must be loaded into internal memory first. Motions share memory with patterns: Memory Full! means patterns or motions must be deleted. REMOTE KBD IN receives only temporary patch and performance parameters. JP-8000 dumps can be received, but JP-8080-only parameters keep their previous values unless the temporary area is initialized first; JP-8000 patterns are not accepted.

Source: Roland JP-8080 Owner's Manual (1998), pp. 123-124, 137-139 and MIDI implementation ↗

Specifications

Synthesis
Analog modeling (virtual analogue), same sound source as the JP-8000
Polyphony
10 voices (8 with the Voice Modulator on)
Multitimbrality
2 parts (Upper, Lower): Single, Dual or Split
Oscillators
2 per voice. OSC 1: Super Saw, Triangle Mod, Noise, Feedback Osc, Square (PWM), Saw, Triangle. OSC 2: Square (PWM), Saw, Triangle, Noise
Filter
High-pass, band-pass or low-pass, -12 or -24 dB/octave
Memory
128 user and 384 preset patches; 64 user and 192 preset performances; SmartMedia card slot
Keyboard / format
Rack module (482 x 88 x 264 mm; 6U according to Sound On Sound)
Outputs
Output L (mono) and R, headphones; inputs INST/LOWER, VOCAL/UPPER and MIC
MIDI
MIDI In, Out, Remote Keyboard In (no Thru)

Known issues and maintenance

Backup battery. An internal battery keeps the memory while the power is off. When it runs low the display shows Battery Low! and the battery should be replaced by a Roland service centre to avoid losing the user memory.

Sources

to be verified

These notes have not been checked against the sources yet. Corrections are welcome in the comments.

  1. Roland JP-8080 Owner's Manual (1998) ↗ — Features p. 11, MIDI settings pp. 123-124, Bulk Dump and restore pp. 137-139, MIDI implementation (model ID 00H 06H, RQ1, 20 ms rule), specifications pp. 209-210, battery note
  2. Paul Ward, "Roland JP8080", Sound On Sound, November 1998 ↗ — Review: rack version of the JP-8000, 6U height, SysEx only on the normal MIDI input, no MIDI Thru, verdict

Comments

0

Sign in to write a comment.

An unhandled error has occurred. Reload 🗙

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.