Roland Juno-D
The Roland Juno-D is a 61-key synthesizer with documentation dated 2004 and a Sound On Sound review in March 2005. Despite the name it is a sample-based instrument from Roland's PCM range: it plays 64 voices over 16 parts from 32 MB of waveforms, each patch uses up to two tones, and it adds phrase and arpeggio templates, a rhythm guide and a D Beam controller. It stores 128 user patches, 2 rhythm sets and 8 performances. The XFER to MIDI function sends the current patch or performance, a single user patch or performance, or the whole user area (patches, performances, system settings) as System Exclusive messages. Sending the recorded data back to MIDI In restores it, and a computer can also request user patches and performances directly.
Sign in to upload or commentSysEx messages
0 filesThis instrument is still waiting for its first SysEx.
If you own one, or can recover a dump from an old disk or backup, upload it here: every message helps the library and the community grow.
Upload a SysExSysEx guide
- Manufacturer ID
- 41
- Model ID
- 00 64
- Default device ID
- Device ID 17-32 (dev byte 10H-1FH)
- Suggested delay between messages
- 20 ms
Receiving a dump
1. In SYSTEM, set Rx Sys Exc (System Exclusive Receive Switch) to ON. It is ON with the factory settings. 2. Set Device ID to the number used when the data was recorded. 3. Play the data back to MIDI In at the tempo used when it was recorded, and do not operate the Juno-D while it is receiving.
Sending a dump from the instrument
1. Press PATCH so it is lit (Patch mode). 2. Press UTILITY. 3. Use PAGE/CURSOR to select 4:XFER to MIDI and press ENTER. 4. Use VALUE -/+ to choose what to send: CURRENT PATCH, a user patch, or DUMP ALL for the whole user area. 5. Start recording on the sequencer and press ENTER. The display shows COMPLETED when done. In Performance mode the same function is 3:XFER to MIDI, with CUR PERFORM, USER PERFORM or DUMP ALL.
Requesting a dump
Send a Roland data request RQ1: F0 41, device ID, 00 64 11, a 4-byte address, a 4-byte size, the checksum and F7. Main addresses: 00 00 00 00 setup, 01 00 00 00 system, 20 00 00 00 user performances (8), 30 00 00 00 user patches (128), 40 00 00 00 user rhythm sets (2).
SysEx pitfalls
If the Device ID or Rx Sys Exc setting is wrong, or the sequencer tempo differs from the recording, the data may not be received. Data larger than 256 bytes is split into packets sent about 20 ms apart.
Specifications
- Synthesis
- Sample-based (PCM waveforms), two tones per patch
- Polyphony
- 64 voices
- Multitimbrality
- 16 parts
- Oscillators
- 32 MB wave memory, 640 original tones; two tones per patch, split or layered
- Memory
- 128 user patches, 2 user rhythm sets, 8 user performances; 640 preset patches (384 plus 256 GM2), 20 rhythm sets, 32 performances
- Keyboard / format
- 61 keys with velocity
- Outputs
- L/mono, R, headphones
- MIDI
- MIDI In, Out
Sources
to be verifiedThese notes have not been checked against the sources yet. Corrections are welcome in the comments.
- Roland JUNO-D Owner's Manual (2004) ↗ — XFER to MIDI pp. 51 and 61, MIDI system settings pp. 90-91, backup p. 98, specifications p. 125
- Roland JUNO-D MIDI Implementation, version 1.00 (2004) ↗ — Model ID 00H 64H, RQ1, DT1, 20 ms packet interval, parameter address map with user memory
- Paul Nagle, "Roland Juno-D", Sound On Sound, March 2005 ↗ — Review: price, PCM roots, no aftertouch, no MIDI Thru, editor and librarian, verdict
Sign in to write a comment.
Comments
0