no image yet
Roland · Synthesizer · 1993

Roland JV-1000

The Roland JV-1000 Music Workstation, from 1993, puts a synthesizer and a sequencer in one instrument with a 76-key keyboard that responds to velocity and channel aftertouch. Each section has its own display and controls. The synthesizer plays 28 voices: a patch is built from up to four tones, and each tone reads a sampled waveform and passes it through a filter (low-pass or high-pass, with resonance) and an amplifier, with envelopes and two LFOs. A performance combines seven patches and a rhythm set. The sequencer has eight phrase tracks, a rhythm track, a tempo track and a 3.5 inch disk drive. The synthesizer side descends from the JV-80, whose preset banks it can still call up, and the sequencer from the MC-50 MkII, as Music Technology noted in its October 1993 review. Slots and bays take a PCM card, a DATA card, a wave expansion board of the SR-JV80 series and a VE voice expansion board. The internal memory holds 64 patches, 16 performances and one rhythm set. With the Bulk command they can be sent as Roland System Exclusive messages to the JV-1000's own sequencer or to an external one, together or one temporary area at a time; a computer can also ask for any block with a data request. The exclusive format and address map are those of the JV-880, so files on this page are sets of short Data Set messages with model ID 46.

SysEx messages

0 files

This instrument is still waiting for its first SysEx.

If you own one, or can recover a dump from an old disk or backup, upload it here: every message helps the library and the community grow.

Upload a SysEx

SysEx guide

Manufacturer ID
41
Model ID
46
Default device ID
Unit number 17 (device ID 10H); range 17-32, device ID = unit number minus 1

Receiving a dump

1. Press MIDI and go to the SYS-EX MIDI page. 2. Set Receive (exclusive receive switch) to ON. 3. Set Unit-No to the unit number the dump was made with (17 = device ID 10 in the file). 4. Press WRITE, choose Protect and set Exclusive protect to OFF. It is OFF after every power-on. With Exclusive protect OFF, received data overwrites the internal memory even if Internal protect is ON.

Sending a dump from the instrument

1. Press WRITE: the display shows WRITE MODE. 2. Select Bulk and press ENTER. 3. Choose Internal, Card or Temporary and press ENTER (for Temporary choose Performance, Patch, Rhythm or All). 4. Set Remote ON to start and stop the sequencer automatically, or OFF. 5. Press ENTER: the display shows Now Sending, then Complete.

Requesting a dump

The JV-1000 answers a Data Request 1 (RQ1): F0 41, device ID, 46 11, a 4-byte address, a 4-byte size, checksum, F7. It does not send RQ1 itself. Main addresses: 00 00 00 00 system common, 00 00 10 00 temporary performance, 01 00 10 00 internal performances, 01 40 20 00 internal patches, 01 7F 40 00 internal rhythm setup, 02 xx xx xx card.

SysEx pitfalls

Transmission is one way, without handshake. The unit number of sender and receiver must match. GS messages (model 42) are ignored except scale tune. Parameters marked % in the address map are for the JV-880 only. MIDI Communication Error means too much data arrived at once: slow the transfer down.

Source: Roland JV-1000 Synthesizer Manual, MIDI pp. 38-39, Commands pp. 100 and 109-111, Error Messages p. 142, MIDI Implementation pp. 177-181 ↗

Specifications

Synthesis
PCM waveforms (wave generator) with a filter and an amplifier per tone; up to 4 tones per patch
Polyphony
28 voices (more with a VE voice expansion board)
Multitimbrality
Performance of 7 patch parts plus a rhythm part (part 8)
Oscillators
Up to 4 tones per patch, each reading a waveform from the internal ROM, a PCM card or a wave expansion board
Filter
One TVF per tone: low-pass or high-pass (or off), with cutoff and resonance
Memory
64 internal patches, 16 performances, 1 rhythm set; 256 factory patches, 64 performances, 4 rhythm sets; DATA card with the same internal capacity
Keyboard / format
76 keys with velocity and channel aftertouch
Outputs
Mix L (mono)/R, V-Exp L (mono)/R, headphones
MIDI
In, Out, Thru, Sequencer Out

Known issues and maintenance

An internal backup battery keeps the user memory. When it runs down the display shows Internal Battery Low and Roland advises contacting a service centre; Internal RAM Read Error means the internal data has been corrupted (Synthesizer Manual p. 142). DATA cards have their own battery (DATA Card Battery Low).

Sources

to be verified

These notes have not been checked against the sources yet. Corrections are welcome in the comments.

  1. Roland JV-1000 Music Workstation Synthesizer Manual (1993), scanned PDF read as page images ↗ — Patch and tone structure p. 5, SYS-EX MIDI page p. 39, TVF p. 61, Write mode p. 100, Bulk and Protect pp. 109-111, error messages p. 142, MIDI Implementation (version 1.00) pp. 177-181 with model ID 46H and the address map shared with the JV-880
  2. Roland JV-1000 Introductory Manual, scanned PDF read as page images ↗ — Sound-generating section p. 14 (28 notes), Specifications p. 97: keyboard, memory, connectors, sequencer, options; lithium battery notice
  3. Simon Trask, "Roland JV-1000", Music Technology, October 1993 ↗ — Launch review: JV-80 based synth section and MC-50 MkII based sequencer, expansion boards, UK prices, criticisms

Comments

0

Sign in to write a comment.

An unhandled error has occurred. Reload 🗙

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.