no image yet
Roland · Synthesizer · 1999

Roland MC-307

The Roland MC-307 Groovebox, from 1999, sits between the MC-303 and the MC-505: a tabletop sequencer and sound module for dance music, aimed at DJs. Its sound generator plays 64 voices over eight main parts plus 16 RPS parts, which trigger phrases from the 16 keyboard pads. It holds 800 preset and 256 user patches, 40 preset and 20 user rhythm sets, 240 preset patterns, 470 RPS phrases, 200 user patterns and 50 songs. Effects are reverb, delay and 25 multi-effects. Its own additions are a Turntable Emulation slider that bends pitch and tempo like a record, and a GRAB switch. Sound On Sound called it a slimmed-down MC-505 with more presets: patches of up to four tones, each with a multi-mode filter, two LFOs and three envelopes. It has a single stereo output and no memory card slot, so patches and patterns are kept on an external sequencer. That is done with Bulk Dump. It sends the selected pattern (its setup, its patches, or the musical data as well) or the whole user memory, about 1.1 MB taking roughly nine minutes, as Roland System Exclusive data with model ID 00 0B. Roland says messages common to the MC-505 and JX-305 can be exchanged, and the MC-307 accepts MC-505 bulk dumps, though the MC-505 may not accept the MC-307's.

SysEx messages

0 files

This instrument is still waiting for its first SysEx.

If you own one, or can recover a dump from an old disk or backup, upload it here: every message helps the library and the community grow.

Upload a SysEx

SysEx guide

Manufacturer ID
41
Model ID
00 0B
Default device ID
Device ID 17-32 (byte 10H-1FH); factory value not stated in the pages read

Receiving a dump

1. Press SYSTEM, then F1 (SYS), press CURSOR up, then F4 (MIDI). 2. Press F1 (CMN) and set DEVICE ID to the number used when the dump was made. 3. Press F2 (TXRX) and set RX.SYSEX to ON. 4. For a pattern dump: press PTN, select the destination pattern, then SYSTEM, F2 (UTIL), CURSOR up, F3 (BULK), F2 (RX) and play the dump. For the whole user memory: SYSTEM, F2 (UTIL), CURSOR up, F3 (BULK), F4 (RX AL), F4 (EXEC), then play the dump.

Sending a dump from the instrument

Selected pattern: 1. Press PTN and select the pattern. 2. Press SYSTEM, F2 (UTIL), CURSOR up, F3 (BULK), F1 (TX). 3. Choose SETUP, SETUP&PATCH or the full pattern data with the cursor. 4. Start recording on the sequencer, press F4 (SEL), then F4 (EXEC). All user data: SYSTEM, F2 (UTIL), CURSOR up, F3 (BULK), F3 (TXAL), start recording, F4 (EXEC). It takes about nine minutes and about 1.1 MB.

Requesting a dump

Data Request 1 (RQ1): F0 41, device ID (10-1F), 00 0B 11, a 4-byte address, a 4-byte size, checksum, F7. The answer is a series of Data Set 1 (DT1) messages. Main addresses: 00 00 00 00 system, 01 00 00 00 part info, 02 00 00 00 temporary patches.

SysEx pitfalls

Received pattern data stays in the temporary area until written with Patch Write and Pattern Write. The MC-505 may refuse MC-307 bulk dumps because of the different number of patches. The MC-307 calculates checksums of exclusive messages typed in its microscope editor unless AUTO CHECKSUM is OFF. Model ID 3A (MC-307 Quick) is used for real-time knob messages.

Source: Roland MC-307 Owner's Manual, microscope p. 73, MIDI settings pp. 123-126, Bulk Dump pp. 129-130, MIDI Implementation pp. 194-201 ↗

Specifications

Synthesis
Sample-based (PCM waveforms) with filter and amplifier per tone; up to 4 tones per patch
Polyphony
64 voices
Multitimbrality
24 parts (8 main + 16 RPS)
Oscillators
Up to 4 tones per patch
Filter
One filter per tone: LPF, BPF, HPF or peaking (PKG), or off; cutoff and resonance
Memory
800 preset and 256 user patches; 40 preset and 20 user rhythm sets; 240 preset, 470 RPS and 200 user patterns; 50 songs
Keyboard / format
Tabletop groovebox with 16 keyboard pads
Outputs
Output L (mono), R; headphones
MIDI
In, Out (Out can act as Thru)

Known issues and maintenance

Entering the bulk dump reception screen clears the pattern being edited: write any unsaved pattern first. Factory Reset restores all settings, so Roland advises a bulk dump of the user memory first (owner's manual pp. 129-131). Roland publishes system update 1.03 as the latest operating system.

Sources

to be verified

These notes have not been checked against the sources yet. Corrections are welcome in the comments.

  1. Roland MC-307 Groovebox Owner's Manual (1999), text extracted with pdftotext from the fetch tool's copy ↗ — Compatibility with MC-505 and JX-305 p. 73, device ID and Rx System Exclusive pp. 123-126, Bulk Dump pp. 129-130, Main Specifications p. 193, MIDI Implementation (version 1.01, Feb. 22, 2000) with model ID 00 0BH and the address map, implementation chart dated Oct. 27, 1999
  2. Paul Nagle, "Roland MC307", Sound On Sound ↗ — Review: slimmed-down MC-505, sound engine, single stereo output, no SmartMedia slot, criticisms. The fetch tool gave the issue as June 2001
  3. Roland MC-307 product and downloads pages ↗ — Discontinued product, aimed at DJs; system update 1.03 described as the latest operating system; patch, pattern and rhythm kit lists

Comments

0

Sign in to write a comment.

An unhandled error has occurred. Reload 🗙

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.