no image yet
Roland · Synthesizer · 2002

Roland MC-909

The Roland MC-909 is a sampling groovebox from 2002 that puts a 16-part synthesizer, a pattern sequencer and a phrase sampler in one tabletop unit. The sound engine plays up to 64 voices from 693 internal waves and user samples recorded at 44.1 kHz, with 800 preset patches and 72 preset rhythm sets. It can be expanded with one SRX wave board and up to 256 MB of DIMM sample memory, and adds velocity pads, twin D Beam controllers, a turntable emulation slider and a mastering compressor. The MC-909 uses Roland System Exclusive messages with model ID 00H 59H. They cover system settings and the temporary patches and rhythm sets of the 16 parts, which can be edited or read back with data requests. The manual describes no front-panel bulk dump: user patches, patterns and samples are saved to SmartMedia cards or copied to a computer over USB.

Sign in to upload or comment

SysEx messages

0 files

This instrument is still waiting for its first SysEx.

If you own one, or can recover a dump from an old disk or backup, upload it here: every message helps the library and the community grow.

Upload a SysEx

SysEx guide

Manufacturer ID
41
Model ID
00 59
Default device ID
Device ID 17 (range 17-32); dev byte 10H-1FH
Suggested delay between messages
20 ms

Receiving a dump

1. In the System settings, MIDI Rx page, set Receive Exclusive to ON. 2. Set Device ID to the value used by the sending device (factory setting 17).

Requesting a dump

Send a Roland data request RQ1: F0 41, device ID, 00 59 11, a 4-byte address, a 4-byte size, the checksum and F7. If the address and size are valid the MC-909 answers with DT1 messages; otherwise it sends nothing. The address map covers Setup, System, Part Info and the temporary patch or rhythm set of each of the 16 parts.

SysEx pitfalls

The address map contains no user patch area: SysEx gives access only to system settings and the patches currently loaded in the parts. Data over 256 bytes is sent in packets about 20 ms apart. A separate Quick SysEx map (model ID 5DH) is used for knob and slider data.

Source: Roland MC-909 MIDI Implementation v1.00 (2002), Data Transmission and Parameter Address Map; Owner's Manual pp. 128-129 ↗

Specifications

Synthesis
Sample-based (PCM waves and user samples), with sampler and pattern sequencer
Polyphony
64 voices, shared with the sampling section
Multitimbrality
16 parts plus 16 RPS parts
Memory
Patches: 800 preset, 256 user, 256 card. Rhythm sets: 72 preset, 128 user, 128 card. Patterns: 215 preset, 200 user, 999 card
Keyboard / format
Tabletop groovebox with velocity pads (no keyboard)
Outputs
Mix out L/R, Direct 1 L/R, Direct 2 L/R, headphones; input L/R; optical and coaxial digital in/out
MIDI
MIDI In, Out; USB

Known issues and maintenance

Sample memory and the optional DIMM are cleared at power-off: samples must be written to the user area or a SmartMedia card. A Factory Reset erases the internal user memory.

Sources

to be verified

These notes have not been checked against the sources yet. Corrections are welcome in the comments.

  1. Roland MC-909 MIDI Implementation, Version 1.00, Sep. 20, 2002 ↗ — Model ID 00H 59H, RQ1 and DT1 formats, 20 ms packet interval, parameter address map
  2. Roland MC-909 Owner's Manual (2002) ↗ — Features p. 13, memory and storage pp. 19-20, MIDI system parameters pp. 128-129, specifications pp. 175-176
  3. Debbie Poyser and Derek Johnson, "Roland MC909", Sound On Sound, March 2003 ↗ — Review: sampler, SmartMedia and USB backup, polyphony, build quality, verdict

Comments

0

Sign in to write a comment.

An unhandled error has occurred. Reload 🗙

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.