Roland R-8M
The Roland R-8M is a one-unit rack percussion sound module from 1989, the module version of the R-8 drum machine. It has 68 internal drum and percussion sounds sampled at 44.1 kHz, 12-note polyphony, six multi outputs and a stereo mix output, and three slots for SN-R8 sound cards. Sound On Sound noted that it shares its internal sounds with the R-8 but has no pattern sequencer of its own: it is played from a sequencer, drum pads or another drum machine. Sounds are organised in 32 patches, which assign instruments to notes, and 16 feel patches, which vary how instruments respond; a RAM card holds another set. The bulk dump function sends patches, feel patches and setup data, from internal memory or the RAM card, as Roland System Exclusive messages, and the R-8M can load them back.
Sign in to upload or commentSysEx messages
0 filesThis instrument is still waiting for its first SysEx.
If you own one, or can recover a dump from an old disk or backup, upload it here: every message helps the library and the community grow.
Upload a SysExSysEx guide
- Manufacturer ID
- 41
- Model ID
- 36
- Default device ID
- Control channel minus 1 (Control Ch 1-16 sets device ID 00-0F)
Receiving a dump
1. Set the R-8M control channel (EDIT, SETUP, MIDI, Control Ch) to the channel used when the dump was made. 2. Set the exclusive switch (SysEx) on the same page to ON. 3. To write the internal memory, turn Memory Protect off (EDIT, SETUP, PROTECT). To write a RAM card, insert it and turn its protect switch off. 4. Send the data. The display shows Receiving SysEx. The data replaces the previous settings.
Sending a dump from the instrument
1. Set the R-8M control channel to the basic channel of the receiving device. 2. Press EDIT, choose UTIL with the cursor buttons and press ENTER, then choose BULK and press ENTER. 3. Choose ALL, PATCH, FEEL or SETUP and press ENTER; except for SETUP, choose the data (INT, CARD, INT & CARD, TMP or a single patch number). 4. Press ENTER: the display asks Are you sure? 5. Press ENTER to send (EXIT aborts). The display shows Transmitting. 6. Hold JUMP and press EXIT to return to Play mode.
Requesting a dump
The MIDI implementation documents a Roland data request RQ1: F0 41, device ID, 36 11, a 3-byte address, a 3-byte size, the checksum and F7. Bulk dump area addresses include 10 00 00 temporary patch, 12 00 00 to 15 70 00 patches I-01 to I-32, 16 00 00 to 16 2D 00 feel patches I-01 to I-16.
SysEx pitfalls
With Memory Protect on, received exclusive messages do not change the internal memory even with the SysEx switch on. The R-8M does not receive while playing the ROM demo, loading or saving a RAM card, sending a bulk dump or checking a sound card. The device ID byte is the control channel minus 1.
Source: Roland R-8M Owner's Manual (1989), pp. 55-56, 63-64 and MIDI implementation pp. 120-124 ↗
Specifications
- Synthesis
- PCM sample playback, 44.1 kHz, 16 bit
- Polyphony
- 12 notes
- Oscillators
- 68 internal sounds; up to 3 SN-R8 sound ROM cards
- Memory
- 32 patches, 16 feel patches, 1 setup; the same again on an M-256E RAM card
- Keyboard / format
- 1U rack module (EIA-1U)
- Outputs
- Multi out 1-6, Mix out L (mono) and R, headphones
- MIDI
- MIDI In, Out, Thru
Sources
to be verifiedThese notes have not been checked against the sources yet. Corrections are welcome in the comments.
- Roland R-8M Owner's Manual (1989) ↗ — Scanned PDF read as page images. MIDI settings and memory protect pp. 55-56, bulk dump and bulk load pp. 63-64, MIDI implementation dated Oct. 23 1989 (model ID 36H, RQ1/DT1, address map) p. 124, specifications p. 130, instrument list
- David Brenton, "Roland R8M: Total Percussion Sound Module", Sound On Sound, April 1990 ↗ — Review: same internal sounds as the R-8, no pattern programming, 12-note polyphony, rear panel, UK price
Sign in to write a comment.
Comments
0