Roland S-10
The Roland S-10 is a 12-bit sampling keyboard from 1986 and Roland's first low-cost sampler. It has a 49-key velocity-sensitive keyboard, eight voices and a sample memory split into four banks, A to D, which can hold four separate sounds or be combined for longer samples. Samples are recorded through the rear input and stored on 2.8-inch Quick Disks. Reviews give 30 kHz as the standard rate with a 15 kHz option, for 4.4 or 8.8 seconds in total. Each sound has wave parameters such as loop points, envelope and key follow, and performance settings such as vibrato, arpeggio, delay, detune and split. UK reviewers in 1986 praised its ease of use and price under 1,000 pounds, and criticised the short four-octave keyboard. The S-10 uses Roland exclusive messages in two ways. In normal mode it sends and receives single parameter changes as they are edited. In sample data dump mode it transmits or receives the complete samples of the chosen structure, followed by their wave and performance parameters, either one-way or with handshaking. Roland's S-220 manual says data can be copied this way between the S-220, MKS-100 and S-10.
SysEx messages
0 filesThis instrument is still waiting for its first SysEx.
If you own one, or can recover a dump from an old disk or backup, upload it here: every message helps the library and the community grow.
Upload a SysExSysEx guide
- Manufacturer ID
- 41
- Model ID
- 10
- Default device ID
- MIDI basic channel minus 1 (channel 1 = 00)
Receiving a dump
1. Press MIDI. 2. Use Forward/Backward to reach EXCLUSIVE. 3. Turn the Alpha dial to ON (receive and transmit). 4. Press Enter. 5. Set both units to the same MIDI channel. 6. For a sample transfer, put the receiver in sample data dump mode: press F1 and MIDI, then Forward to Sample Data Rcv (one-way) or Sample Data Rcv* (handshake).
Sending a dump from the instrument
1. Select the sampling structure to send. 2. Press F1 and MIDI: the display shows Sample Data Xmt (one-way transmit). 3. Press Forward for Sample Data Xmt* (handshake transmit) if the receiver's MIDI Out is connected back. 4. Press Enter to start. The S-10 sends wave data, then wave parameters, then performance parameters.
Requesting a dump
In sample data dump mode a receiver can ask for data with RQD (41H): F0 41 0n 10 41, 3-byte address, 3-byte size, checksum, F7. Wave data addresses: 02 00 00 bank A, 06 00 00 bank B, 0A 00 00 bank C, 0E 00 00 bank D; size 04 00 00 per bank. In normal mode RQ1 (11H) reads single parameters.
SysEx pitfalls
Exclusive is OFF in the manual's display and must be turned on. Normal mode sends one parameter per message. In a sample dump each DT1 carries 128 bytes of wave data; when the receiver is switched to dump mode by message the transmitter should wait more than 10 ms. Handshake uses WSD 40H, RQD 41H, DAT 42H, ACK 43H, EOD 45H, ERR 4EH, RJC 4FH.
Specifications
- Synthesis
- 12-bit sampling, 30 kHz or 15 kHz
- Polyphony
- 8 voices
- Oscillators
- Four sample banks (A-D), 4.4 s in total at 30 kHz
- Memory
- Four banks A-D in RAM; storage on 2.8-inch Quick Disk
- Keyboard / format
- 49 keys (4 octaves) with velocity
- Outputs
- Output with level switch, headphones
- MIDI
- MIDI In, Out, Thru
Sources
to be verifiedThese notes have not been checked against the sources yet. Corrections are welcome in the comments.
- Roland S-10 Digital Sampling Keyboard Owner's Manual, scanned PDF read as page images ↗ — Features p. 2, panel p. 3, MIDI functions and Exclusive switch pp. 60-62, MIDI Implementation Chart v2.00 p. 66, MIDI Implementation pp. 67-72 (model ID 10H, address map, sample data dump mode), specifications p. 73
- Roland S-220 Owner's Manual (1987), scanned PDF read as page images ↗ — Data Transfer, printed p. 95: data can be copied by MIDI exclusive between S-220, MKS-100 and S-10; MIDI implementation gives model ID 10H for S-10, MKS-100 and S-220
- Julian Colbeck, "Roland S-10 Sampling Keyboard", Sound On Sound, November 1986 ↗ — Review: 12-bit, 128K, 30/15 kHz, 1.1 s per bank, 8 voices, price GBP 999
Sign in to write a comment.
Comments
0