no image yet
Roland · Sound Module · 1991

Roland SC-55

The Roland SC-55 Sound Canvas is a half-rack GS sound module from 1991. It plays 16 parts at once with up to 24 voices, using Roland's RS-PCM sampled sounds, and adds reverb and chorus. A large display shows the level of every part, and the unit came with an infrared remote control. Sound On Sound counted 128 basic instruments plus variation sounds and drum sets. The Sound Canvas can send its settings as Roland System Exclusive messages: all overall and part settings, or a single part, recorded into a sequencer and played back later to restore them. Parameters can also be changed one at a time with exclusive messages.

Sign in to upload or comment

SysEx messages

0 files

This instrument is still waiting for its first SysEx.

If you own one, or can recover a dump from an old disk or backup, upload it here: every message helps the library and the community grow.

Upload a SysEx

SysEx guide

Manufacturer ID
41
Model ID
42 (GS), 45 (SC-55 display)
Default device ID
Device ID 17 (range 1-32); dev byte 00H-1FH
Suggested delay between messages
20 ms

Receiving a dump

1. Connect the sequencer's MIDI OUT to the Sound Canvas MIDI IN. 2. Make sure the device ID matches the one used when the data was sent (press ALL, then use the MIDI CH buttons). 3. Make sure Rx SysEx is On (factory setting): press ALL, press both PART buttons, choose Rx SysEx with ALL and MUTE, set On with INSTRUMENT right, then press both PART buttons. 4. Play the exclusive messages from the sequencer; no special receive mode is needed.

Sending a dump from the instrument

1. Connect the Sound Canvas MIDI OUT to the sequencer's MIDI IN. 2. Press ALL so that its indicator lights. 3. Press both INSTRUMENT buttons together. The display shows Dump All, Sure? 4. Start recording on the sequencer. 5. Press ALL to transmit (MUTE stops the transfer). 6. Stop recording. For all parts plus part settings (Dump ALL+), press both PART buttons before step 3. For one part (Dump PART), turn ALL off, then press both PART buttons and both INSTRUMENT buttons.

Requesting a dump

The SC-55 accepts the Roland data request RQ1 (11H): F0 41, device ID, model ID 42, 11, a 3-byte address, a 3-byte size, checksum, F7. It answers with DT1 (12H). Bulk dump blocks start at address 48 00 00 (patch parameters) and 49 00 00 (drum setup).

SysEx pitfalls

Only the one-way procedure is supported. Muted parts are not sent by Dump ALL+. The partial reserve is sent as one setting for all parts. If the device ID differs from the one in the data, the messages are not received correctly.

Source: Roland SC-55 Sound Canvas Owner's Manual (1991), pp. 50-53, 72, 77 ↗

Specifications

Synthesis
RS-PCM sample playback, GS Standard
Polyphony
24 voices (partials)
Multitimbrality
16 parts (two can be drum parts)
Keyboard / format
Half-rack module
Outputs
Stereo audio output (L, R), headphones; stereo audio input for mixing another source
MIDI
2 MIDI In (front and rear), Out, Thru

Sources

to be verified

These notes have not been checked against the sources yet. Corrections are welcome in the comments.

  1. Roland SC-55 Sound Canvas Owner's Manual (1991) ↗ — Features p. 3, dump and receive procedures pp. 50-53, Roland exclusive format p. 72, model IDs and address map p. 77, specifications p. 86
  2. Paul D. Lehrman, "Roland SC55 Sound Canvas", Sound On Sound, September 1991 ↗ — Review: RS-PCM, 128 instruments plus variations, 24 voices, 16 parts, MT-32 emulation

Comments

0

Sign in to write a comment.

An unhandled error has occurred. Reload 🗙

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.