Roland SH-32

Photo: Soundifical · CC BY-SA 4.0 ↗

Roland · Synthesizer · 2001

Roland SH-32

The Roland SH-32 is a compact desktop synthesizer from 2001, without a keyboard, played from MIDI or from thirteen panel buttons that work as note keys. It is a virtual analogue instrument: each patch has two oscillators with 67 waveforms, a sub-oscillator, sync and ring modulation, a multimode filter with a 12 or 24 dB slope, an amplifier and two LFOs. It has 32 voices, halved when both oscillators are used, and four parts, so it can play a bass, two synth lines and a drum part made from 63 drum waveforms that include TR-909 and TR-808 sounds. The panel uses knobs and sliders like an analogue synth, with a three-character LED display. An arpeggiator with 64 arpeggio and 64 rhythm styles and a chord memory complete it. Sound On Sound described it in 2002 as Roland's first SH-named synth since the early 1980s and praised its sound and rhythm section, while finding the display and editing awkward. The SH-32 can send its settings as System Exclusive bulk dumps from the panel: everything at once, the sounds (patches, rhythm sets and performances), the styles, the chord forms, the system settings or just the sound being edited. Sending a dump back overwrites the user memory. The dumps use Roland's model ID 00 4A and can also be requested from a computer.

SysEx messages

0 files

This instrument is still waiting for its first SysEx.

If you own one, or can recover a dump from an old disk or backup, upload it here: every message helps the library and the community grow.

Upload a SysEx

SysEx guide

Manufacturer ID
41
Model ID
00 4A
Default device ID
Device ID 17 (dev byte 10H); range 17-32
Suggested delay between messages
20 ms

Receiving a dump

1. No receive menu: send the dump into MIDI IN. 2. The device ID must be the one used when the dump was made: power on holding [5] to set it (17-32), then power off and on. 3. In TxM mode MODE 1 (power on holding [4/D]) exclusive messages are always received. 4. Play the file back at the tempo used when it was recorded. A full dump overwrites the user and system memory.

Sending a dump from the instrument

1. Connect MIDI OUT to the receiver. 2. Turn the FX/SYSTEM knob to SYSTEM. 3. Press [8/R (BULK DUMP)] so that it blinks. 4. Choose the data with VALUE: ALL, Sou (patches, rhythm sets, performances), ArP (arpeggio and rhythm styles), CHd (chord forms), SyS (system), or one temporary item (1PA, 1PF, 1rH, 1AP, 1Cd). 5. Start the recorder and press [WRITE (EXEC)]. The display shows Ok when done. 6. Press [EXIT].

Requesting a dump

Send a Roland data request RQ1: F0 41, device ID, 00 4A 11, a 4-byte address, a 4-byte size, checksum, F7. Addresses: 00 00 00 00 system, 20 00 00 00 to 20 3F 00 00 performances, 30 00 00 00 to 30 7F 00 00 patches A11-B88, 40 00 00 00 and 40 10 00 00 user rhythm sets, 50 00 00 00 styles, 60 00 00 00 chord forms. Requests must use the fixed start addresses and sizes of the map.

SysEx pitfalls

The SH-32 sends data over 256 bytes in packets about 20 ms apart. A different device ID makes the unit ignore the dump. Too much data at once gives a MIDI buffer full error, a damaged file a checksum error. Patches C11-D88 are read only.

Source: Roland SH-32 Owner's Manual pp. 88-89, 93, 98; SH-32 MIDI Implementation v1.00 pp. 4-6 ↗

Specifications

Synthesis
Virtual analogue (Roland Wave Acceleration Synthesis) with oscillator sync, ring modulation and PWM
Polyphony
32 voices; halved for patches that use both oscillators
Multitimbrality
4 parts
Oscillators
2 oscillators per patch plus sub-oscillator; 67 waveforms in 7 groups; 63 drum waveforms for rhythm sets
Filter
One per voice: LPF, BPF, HPF or peaking, -12 or -24 dB/octave, with resonance
Memory
128 user and 128 preset patches; 64 performances; 2 user and 2 preset rhythm sets; 64 arpeggio, 64 rhythm styles, 64 chord forms
Keyboard / format
Desktop module without keyboard; 13 note-entry buttons
Outputs
Output L and R (1/4 inch), headphones
MIDI
MIDI In, Out

Known issues and maintenance

An internal battery keeps the user memory; when the display reports a low battery, have it replaced by a Roland service centre and back up the data first. Factory Reset (power on while holding 1/A) restores the factory data, all or by type. The Low Boost function is on from the factory and can be turned off at power-on with 2/B.

Sources

to be verified

These notes have not been checked against the sources yet. Corrections are welcome in the comments.

  1. Roland SH-32 MIDI Implementation, Version 1.00, Dec. 12, 2001 ↗ — Model ID 00H 4AH, device ID 10H default, RQ1/DT1, 20 ms packets, parameter address map
  2. Roland SH-32 Owner's Manual (2001) ↗ — Specifications p. 117, filter p. 56, bulk dump p. 88, TxM mode and device ID p. 93, factory reset p. 94, battery and error messages
  3. Roland SH-32 product page ↗ — Product description; marked Discontinued
  4. Gordon Reid, "Roland SH32", Sound On Sound, May 2002 ↗ — Review: polyphony with one and two oscillators, bulk dump options, criticisms and verdict

Comments

0

Sign in to write a comment.

An unhandled error has occurred. Reload 🗙

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.