no image yet
Roland · Sound Module · 2004

Roland TD-20

The Roland TD-20 is a V-Drums percussion sound module introduced in 2004. Its Variable Drum Modeling engine lets the player edit virtual drums in detail: shell material and depth, head type and tuning, muffling, snare buzz and microphone position. It plays 64 voices from 560 drum and 262 backing instruments, holds 50 drum kits, and has 15 trigger inputs, eight direct outputs, a built-in sequencer with 100 preset and 100 user patterns, and a CompactFlash card slot. The Bulk Dump function sends the whole memory or single parts of it as Roland System Exclusive messages: setup and trigger settings, one or all drum kits, trigger banks, user percussion sets and user patterns. A sequencer records the dump and plays it back to restore the data, provided the Device ID is the same as when it was saved.

Sign in to upload or comment

SysEx messages

0 files

This instrument is still waiting for its first SysEx.

If you own one, or can recover a dump from an old disk or backup, upload it here: every message helps the library and the community grow.

Upload a SysEx

SysEx guide

Manufacturer ID
41
Model ID
00 7A
Default device ID
Device ID 17 (range 1-32); dev byte 10H
Suggested delay between messages
40 ms

Receiving a dump

1. Connect the sequencer's MIDI OUT to the TD-20 MIDI IN. 2. Make sure the TD-20 Device ID (SETUP > MIDI > GLOBAL) is the same as when the dump was saved. 3. Start playback on the sequencer. The received data is written into the TD-20 and overwrites the current data.

Sending a dump from the instrument

1. Connect the TD-20 MIDI OUT to the sequencer's MIDI IN. 2. Press SETUP. 3. Press F1 (MIDI), then F5 (BULK). The MIDI BULK DUMP screen appears. 4. Use +/-, VALUE and CURSOR to choose the data: ALL, SETUP, ALL DRUM KITS or 1 DRUM KIT, ALL TRIG BANKS or 1 TRIG BANK, ALL PERC GROUPS or 1 PERC GROUP, ALL PATTERNS. 5. Start recording on the sequencer. 6. Press F5 (EXECUTE). Press F5 (STOP) to stop sending.

Requesting a dump

The MIDI implementation documents no data request (RQ1) message: dumps are started from the front panel.

SysEx pitfalls

A dump reloads only if the TD-20 Device ID is the same as when it was saved. The sequencer must record System Exclusive messages. DT1 data is divided into packets of 128 bytes or less, with at least 40 ms between successive messages. Receiving overwrites the current data.

Source: Roland TD-20 Owner's Manual (2004), pp. 75 and 77; MIDI Implementation v1.00 (Jan. 25, 2004), p. 9 ↗

Specifications

Synthesis
Variable Drum Modeling (V-EDIT of shells, heads, muffling and mic position)
Polyphony
64 voices
Memory
50 drum kits, 16 kit chains, 8 percussion sets; 100 user and 100 preset patterns; CompactFlash card slot
Keyboard / format
Percussion sound module (307 x 256 x 105 mm) with 15 trigger inputs and hi-hat control jack
Outputs
Master L/Mono and R, 8 direct outputs, coaxial digital out, headphones; mix in
MIDI
MIDI In, Out/Thru

Known issues and maintenance

Backup battery. An internal battery keeps the memory while the power is off. When it runs low the display shows Backup Battery Low! and the battery should be replaced soon through a Roland service centre to avoid losing all data.

Sources

to be verified

These notes have not been checked against the sources yet. Corrections are welcome in the comments.

  1. Roland TD-20 Owner's Manual (2004) ↗ — Battery note, Device ID p. 75, Bulk Dump and reload p. 77, specifications pp. 102-103
  2. Roland TD-20 MIDI Implementation, Version 1.00, Jan. 25, 2004 ↗ — Model ID 00H 7AH, device ID 10H, DT1 format, 128-byte packets and 40 ms interval, address map
  3. Roland 50th Anniversary: 2000s ↗ — Lists the TD-20K V-Drums kit under 2004

Comments

0

Sign in to write a comment.

An unhandled error has occurred. Reload 🗙

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.