no image yet
Roland · Sound Module · 1999

Roland TD-8

The Roland TD-8 is the percussion sound module of the V-Drums series, released in 1999. It is played from pads and cymbals connected to ten dual trigger inputs, and it holds 1,024 drum instruments and 262 backing instruments, with 64 voices of polyphony. Its 64 drum kits can be shaped with V-Edit parameters such as shell depth, head type, tuning and muffling, plus an ambience effect and a two-band master equalizer. A built-in sequencer offers 700 preset patterns, 100 user patterns and 50 user songs, and the module also follows General MIDI, so it can be used as a sound source for a sequencer. The Bulk Dump function sends the setup, the drum kits (all or one), the user percussion sets and the user patterns and songs as Roland System Exclusive messages, which can be recorded on a sequencer and played back to the TD-8 to restore them.

Sign in to upload or comment

SysEx messages

0 files

This instrument is still waiting for its first SysEx.

If you own one, or can recover a dump from an old disk or backup, upload it here: every message helps the library and the community grow.

Upload a SysEx

SysEx guide

Manufacturer ID
41
Model ID
00 20
Default device ID
Device ID 17 (range 1-32); dev byte 10H
Suggested delay between messages
40 ms

Receiving a dump

1. Connect the sequencer's MIDI OUT to the TD-8 MIDI IN. 2. Make sure the TD-8 Device ID matches the one used when the dump was made: press SETUP, F2 (MIDI), F1 (GLOBAL), F3 (PAGE 3) and check DEVICE ID. 3. Play the recorded data from the sequencer to the TD-8. The received data overwrites the TD-8 memory.

Sending a dump from the instrument

1. Connect the TD-8 MIDI OUT to the sequencer's MIDI IN. 2. Press SETUP, then F2 (MIDI), then F3 (BULK). The BULK DUMP screen appears. 3. Use INC/DEC or the VALUE dial to choose the data: ALL, SETUP, DRUM KIT, USER PERC SET or USR PTNS&SONGS. 4. For DRUM KIT and USER PERC SET, move the cursor to the bottom row and choose ALL or a single kit or set. 5. Start recording on the sequencer. 6. Press F3 (EXEC) to send the data (F1 STOP cancels). 7. Stop the sequencer when the completion screen appears.

Requesting a dump

Send a Roland data request RQ1: F0 41, device ID, 00 20 11, a 4-byte address, a 4-byte size, the checksum and F7. Bulk dump request addresses with size 00 00 00 00: 10 00 00 00 all user patterns and songs; 40 00 00 00 setup; 41 mm 00 00 one drum kit (mm 00-3F) or 41 7F 00 00 all kits; 44 nn 00 00 one user percussion set (nn 00-01) or 44 7F 00 00 both. If the address and size are not valid nothing is sent.

SysEx pitfalls

A dump is received only if the TD-8 Device ID equals the one used when it was made: note it down. The SETUP dump does not include Device ID and LCD contrast. Preset patterns 1-700 cannot be transmitted. CHECKSUM ERROR! means a wrong checksum; MIDI BUFFER FULL! means too much data arrived too quickly. The sequencer does not work in GM mode.

Source: Roland TD-8 Owner's Manual (1999), pp. 149-150, 169, 174 and MIDI implementation pp. 202-212 ↗

Specifications

Synthesis
Variable Drum Modeling (sampled drum and backing instruments with V-Edit parameters)
Polyphony
64 voices
Multitimbrality
Drum kit plus backing parts; sequencer with 6 parts; General MIDI mode
Oscillators
1,024 drum instruments and 262 backing instruments
Memory
64 drum kits; 16 drum kit chains; 2 user percussion sets; 700 preset and 100 user patterns; 50 user songs
Keyboard / format
Tabletop or stand-mounted module (293 x 223 x 80 mm); played from pads via 10 dual trigger inputs
Outputs
Master Output L (mono) and R, Direct Output L and R, headphones; Mix In (stereo)
MIDI
MIDI In, Out/Thru

Known issues and maintenance

Backup battery. An internal battery keeps the user memory while the power is off. When it runs low the display shows BACKUP BATTERY LOW!; if it is fully drained the display shows BACKUP NG! EXECUTE FACTORY RESET ALL! and the user data is lost. Roland says the battery should be replaced by a dealer or Roland service centre.

Sources

to be verified

These notes have not been checked against the sources yet. Corrections are welcome in the comments.

  1. Roland TD-8 Owner's Manual (1999) ↗ — Bulk Dump and Device ID pp. 149-150, error messages and battery, MIDI implementation (model ID 00H 20H, RQ1, dump request addresses, 40 ms between DT1 messages), specifications p. 216
  2. Roland TD-8 product page (Roland global) ↗ — Manufacturer description and specifications; marked Discontinued

Comments

0

Sign in to write a comment.

An unhandled error has occurred. Reload 🗙

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.