Waldorf Blofeld
The Waldorf Blofeld is a digital synthesizer built as a small desktop module and as a keyboard version with a four-octave keyboard. Sound On Sound, which reviewed the module in June 2008, describes it as the first product of the re-founded Waldorf Music. Each voice has three oscillators that play either the virtual analog models of the Waldorf Q or the wavetables of the Microwave II and XT, followed by two independent multimode filters with drive stages, three LFOs and four envelopes. The Blofeld plays up to 25 voices and is 16-part multitimbral. With the License SL option it also plays samples from about 60 MB of memory. Reviewer Paul Nagle praised the PPG-style filter and summed the module up as "Microwave and Micro Q power you can put in your pocket!". His main complaint was the single MIDI In socket: the desktop Blofeld has no MIDI Out, and MIDI leaves it only through USB. The memory holds more than 1,000 sounds in eight banks, A to H, and 128 Multi programs. The Blofeld can send one sound, one bank, all sounds, or all sounds with the global settings as System Exclusive data, and Multi programs in the same way. It receives dumps without any special mode, provided the Device ID matches. Waldorf distributes the factory sound sets as MIDI files to be played into the instrument.
Sign in to upload or commentSysEx messages
0 filesThis instrument is still waiting for its first SysEx.
If you own one, or can recover a dump from an old disk or backup, upload it here: every message helps the library and the community grow.
Upload a SysExSysEx guide
- Manufacturer ID
- 3E
- Default device ID
- Device ID 0 (range 0-126; 127 is the broadcast ID)
Receiving a dump
No receive mode is needed: the Blofeld accepts SysEx at MIDI In or USB at any time. 1. Hold Shift and press Global, select Device ID and make sure it matches the ID of the data (0 for a single Blofeld). 2. Leave Edit mode on every program: incoming dumps can overwrite the edit buffers. 3. Start the transmission on the sender.
Sending a dump from the instrument
1. Connect the Blofeld to the computer by USB (the desktop module has no MIDI Out) and start recording SysEx. 2. Hold Shift and press Utility. 3. With the Selection dial choose Dump Sound, Dump Sound Bank, Dump All Sounds or Dump All (all sounds and the global settings). In Multi mode the choices are Dump Multi, Dump Arrangement (the Multi with its sounds) and Dump All Multis. 4. Hold Shift and press Utility again to start. The Blofeld cannot be played until the dump ends.
SysEx pitfalls
Sender and receiver must use the same Device ID, or the broadcast ID 127. A single sound is received into the edit buffer: store it, or it is lost. Banks and complete dumps are written straight to memory and replace what is there. Factory sound sets and firmware are standard MIDI files. Waldorf says to play them from a sequencer at 80 bpm with SysEx transmission enabled, or to send them with SysEx Librarian, MIDI-OX or Waldorf Spectre. Ableton Live and Bitwig cannot send SysEx. A sound set comes as one file per bank: use only the file for the bank you want to overwrite. If a transfer fails, Waldorf suggests setting the Device ID to 0 or 1. In 2008 the Sound On Sound reviewer found patch reception unreliable and had to resend the data slowly.
Source: Waldorf Blofeld User's Manual, printed pp. 81-88 and 109 ↗
Specifications
- Synthesis
- Digital: virtual analog oscillator models from the Waldorf Q and Microwave II/XT/XTk wavetables; sample playback with the License SL option
- Polyphony
- Up to 25 voices
- Multitimbrality
- 16 parts; 128 Multi programs
- Oscillators
- 3 per voice with frequency modulation between them; two can play wavetables, the third only analog models
- Filter
- 2 independent multimode filters per voice with filter FM, and 2 drive stages
- Memory
- More than 1,000 sounds in eight banks (A to H), 128 Multi programs
- Keyboard / format
- Desktop module; Keyboard version with four octaves, velocity and aftertouch
- Outputs
- Stereo output (unbalanced) and headphones
Known issues and maintenance
The message "bad DSP response!" at power-on points to a possible hardware defect: Waldorf asks to contact support. Encoders that skip or jump: update the firmware first. Older units may need new encoders. Waldorf warns against contact cleaner. Windows 11 may not recognise the USB port. This needs OS 1.25 HS, which Waldorf support supplies on request. Multi mode can crash when MIDI channel 10 is used: Waldorf advises avoiding that channel. If the unit hangs, the FAQ gives soft-reset steps or suggests switching it off and on five times in a row. If Contrast was set to 0 and the display is unreadable: switch on, hold Shift and press Global, then turn the left display dial.
Sources
to be verifiedThese notes have not been checked against the sources yet. Corrections are welcome in the comments.
- Waldorf Blofeld User's Manual ↗ — Global menu, Device ID, dump functions, receiving SysEx, system update, technical data, declaration of conformity
- Waldorf: FAQ Blofeld ↗ — How to send sound sets and firmware, factory defaults, eight banks, License SL, known problems, download list
- Waldorf: Blofeld Desktop (product page) ↗ — Specifications: voices, parts, oscillators, filters, connections
- Waldorf: Blofeld Keyboard (product page) ↗ — Keyboard version, sample memory with License SL
- Paul Nagle, "Waldorf Blofeld", Sound On Sound, June 2008 ↗ — Review of the desktop module: architecture, MIDI In only, patch reception problems, verdict
- Paul Nagle, "Waldorf Blofeld Keyboard", Sound On Sound, April 2009 ↗ — Review of the keyboard version: four octaves, aftertouch, sample memory
Sign in to write a comment.
Comments
0