Waldorf Rack Attack

Photo: Brandon Daniel from Sunnyvale, CA, USA · CC BY-SA 2.0 ↗

Waldorf · Drum Machine

Waldorf Rack Attack

The Waldorf RackAttack is a percussion synthesizer in a two-unit 19-inch rack case, presented by Waldorf as the hardware version of its Attack VST instrument. Instead of playing samples it builds drum sounds with virtual modelled circuitry: each sound has two oscillators, a mixer with ring modulation and a Crack modulator, a multimode filter, two envelopes, two LFOs and its own pattern. It covers classic analogue drum machine sounds and club drums, and its sounds can also be played melodically as basses, leads and effects. The memory holds 50 Programs, each a kit of 24 Sounds, and all locations are user-programmable. Up to 24 synchronised patterns can be started by one MIDI note, and four effect units add reverb, modulation delay and Lo-Fi. The rear panel has three stereo output pairs and MIDI In, Out and Thru. Holding Shift and pressing Global/Utility opens the dump page, from which the RackAttack sends its global data, the edit buffer, the current program or all 50 programs as SysEx. It needs no receive mode: a single program arrives in the edit buffer and must be stored. Operating system updates also arrive as SysEx in a Standard MIDI File.

SysEx messages

0 files

This instrument is still waiting for its first SysEx.

If you own one, or can recover a dump from an old disk or backup, upload it here: every message helps the library and the community grow.

Upload a SysEx

SysEx guide

Manufacturer ID
3E
Default device ID
SysEx ID 0 (the manual says to leave it on 0 with a single unit); range 0-126, 127 is broadcast

Receiving a dump

1. Leave all programs out of Edit mode: edit buffers may be cleared or overwritten. 2. Set the SysEx ID in the Global menu to match the dump. 3. Start the sender. No receive mode is needed. 4. Store any single program that arrives in the edit buffer.

Sending a dump from the instrument

1. Press Shift + Global/Utility: the display shows the dump page. 2. Turn the page dial to choose Global Data, Dump Edit Buffer, Dump Program Pxx (current program) or Dump all Programs. 3. Press Shift + Global/Utility again to start. The unit cannot be played during the dump.

SysEx pitfalls

The SysEx ID of sender and receiver must match; ID 127 is accepted by every RackAttack but never sent. Operating system files are sent with ID 127. Single dumps are lost at power-off unless stored.

Source: Waldorf RackAttack User's Manual, January 2003, version 1.04, pp. 74, 80-81, 94

Specifications

Synthesis
Virtual analogue percussion synthesis (virtual modelled circuitry)
Multitimbrality
24 sounds per program on MIDI channels 1-12 (Plug-in mode) or on the global channel
Oscillators
2 oscillators per sound, plus the Crack section in the mixer
Filter
Multimode: 12 dB low pass, high pass, band pass, notch, shelving EQ, bell EQ, S&H
Memory
50 Programs of 24 Sounds each (1,200 sounds), all user-programmable
Keyboard / format
2U 19-inch rack module
Outputs
3 stereo output pairs (usable as 6 mono), headphone jack mirroring Out 1+2
MIDI
In, Out, Thru

Known issues and maintenance

Switching off while a new operating system is being written to flash can cause complete data loss and leave the unit unusable.

Sources

to be verified

These notes have not been checked against the sources yet. Corrections are welcome in the comments.

  1. Waldorf, RackAttack User's Manual, January 2003, version 1.04 — Manufacturer manual in a third-party copy: memory, connections, filter types, SysEx ID, dump and receive procedures, OS update, MIDI chart, technical data
  2. Waldorf, Legacy Rack Attack ↗ — Description: hardware version of the Attack plug-in, patterns, effects; download folders

Comments

0

Sign in to write a comment.

An unhandled error has occurred. Reload 🗙

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.