Yamaha VL70-m
The Yamaha VL70-m is a half-rack tone generator that brought Yamaha's Virtual Acoustic physical modelling to a small, affordable box. Instead of playing samples it models how a reed, lips or a bow drive a pipe or string, so breath, embouchure and growl can be shaped in real time. It plays one note at a time; several units can be linked to share notes. It holds 256 preset voices in two banks, one voiced for keyboard and one for breath or wind control, plus 64 Internal and 6 Custom memories. Inputs for a BC breath controller and a WX wind controller sit on the panel, and a VL-XG mode lets it act as a VL voice inside an XG system. Sound On Sound's October 1996 review found its sounds thinner than the VL1 but called it very nice at under 500 pounds. The Dump Out menu sends system and breath settings, the current voice, or one or all Custom or Internal voices. The unit has no disk drive, so these bulk dumps are how edited voices are saved. In VOICE mode its messages use model ID 57, in VL-XG mode 4C.
Sign in to upload or commentSysEx messages
0 filesThis instrument is still waiting for its first SysEx.
If you own one, or can recover a dump from an old disk or backup, upload it here: every message helps the library and the community grow.
Upload a SysExSysEx guide
- Manufacturer ID
- 43
- Model ID
- 57 (VOICE mode), 4C (VL-XG mode)
- Default device ID
- DevNo. 001-016 or all; all receives on every number but transmits as 001
Receiving a dump
1. Press UTILITY and open the System parameters. 2. Set RcvSysExcl to on. 3. Set DevNo. in the PLAY mode display to match the data, or to all.
Sending a dump from the instrument
1. Press UTILITY and select DUMPOUT. 2. With SELECT choose SYSTEM, CURRENT, CUSTOM or INTERNL and press ENTER. 3. For CUSTOM or INTERNL choose ALL or one voice (C1-C6, I01-I64) with VALUE. 4. Press ENTER; Transmitting appears. 5. Press EXIT when done.
SysEx pitfalls
The receiving unit must have the same device number. DumpIntrval (50-300 ms) sets the pause between blocks; try other values if the receiver reports errors. Some messages carry a checksum; a wrong one gives Check Sum ERROR!
Source: Yamaha VL70-m Owner's Manual (1996), pp. 16, 32, 98-101, 106 ↗
Specifications
- Synthesis
- S/VA Virtual Acoustic physical modelling (VLR algorithm)
- Polyphony
- 1 note (monophonic); Polyphonic Expansion across several units
- Filter
- Dynamic Filter modifier, plus Harmonic Enhancer, Equalizer and Resonator
- Memory
- 256 preset voices (incl. 137 VL-XG voices), 64 Internal and 6 Custom user voices
- Keyboard / format
- Half-rack module without keyboard, 220 x 212 x 46 mm
- Outputs
- OUTPUT L/MONO and R, headphones (stereo mini jack)
- MIDI
- MIDI IN, OUT, THRU, TO HOST serial port; BREATH and WX IN controller inputs
Known issues and maintenance
Backup battery: Battery Low! at power-on means Yamaha service must replace it. Playing the demo initialises system settings and the current voice.
Sources
to be verifiedThese notes have not been checked against the sources yet. Corrections are welcome in the comments.
- Yamaha VL70-m Owner's Manual (1996) ↗ — MIDI data received p. 16, voice organization p. 26, modes pp. 27-30, DevNo. p. 32, utility pp. 98-99, Dump Out pp. 100-101, Show Exclusive p. 103, model IDs and checksum p. 106, specifications p. 113
- Martin Russ, Yamaha VL70m, Sound On Sound, October 1996 ↗ — Review: price, memories, no disk drive, comparison with the VL1, verdict
Sign in to write a comment.
Comments
0