#916 · Data Dump Request
CZ-1000 Current Voice-Channel 2
The Casio CZ-1 is a 61-key digital synthesizer and the model of Casio's CZ range whose keyboard responds to both initial touch and aftertouch; British magazines reviewed it in autumn 1986. It uses the Phase Distortion (PD) sound source: a tone has one or two lines, each with a DCO offering 33 waveforms, a DCW block that shapes the timbre and a DCA, all with eight-step envelopes, and velocity can act on level, timbre and pitch. It plays 16 notes with one-line tones and 8 with two-line tones. The memory holds 64 preset tones and 64 internal tones, which can be named, plus 64 on a cartridge. A further 64 operation memories store Tone Mix (layer) and Key Split set-ups. Over MIDI a multi channel mode plays up to eight tones on separate channels. One Two Testing concluded that 'the advantages far outweigh the small drawbacks'. The CZ-1 sends a single tone, a single operation memory, or all 64 tones and 64 operation memories as System Exclusive data, started from its own panel. Its manual also documents exchanging tones with the CZ-5000 and with the CZ-1000 and CZ-101; in those exchanges names, velocity and level settings are left out.
Sign in to upload or commentIf you own one, or can recover a dump from an old disk or backup, upload it here: every message helps the library and the community grow.
Upload a SysExRelated models: CZ-1000CZ-101CZ-3000CZ-5000
The CZ-1 operation manual describes tone data exchange over MIDI with the other CZ models.
1. Check that the MIDI ON/OFF indicator is lit. 2. Press the MIDI key; in POLY mode set the receive channel (CH) to the sender's channel and PRG to ENA. 3. Press PAGE UP or PAGE DOWN to reach the SYSTEM EXCLUSIVE page and use the VALUE keys to set TONE DATA=ENA. 4. Set the PROTECT switch on the rear panel to OFF. 5. A single tone arrives in the COMPARE/RECALL area and must be written to keep it. After the transfer set TONE DATA=DIS and PROTECT back to ON.
Prepare the CZ-1 as for reception (MIDI on, channels matched, PRG=ENA, TONE DATA=ENA). Single tone: select the tone (A1 to H8; press CARTRIDGE first for a cartridge tone). It is sent as it is selected. Single operation memory: in OPERATION MEMORY mode select the memory. All data: 1. Press CARTRIDGE/MIDI, then PAGE UP or PAGE DOWN until the display shows MIDI SAVE OR LOAD. 2. Press SAVE (VALUE key): SAVE MIDI DATA (Y/N)? 3. Press YES. The 64 internal tones and the 64 operation memories are sent.
From another CZ-1: connect both MIDI cables, set PROTECT OFF on the requesting unit, open MIDI SAVE OR LOAD, press LOAD and then YES; the unit fetches the 64 tones and 64 operation memories. The manual also defines request messages for computers and other CZ models: a send request returns the data of one tone (or one operation memory) for a given number, a receive request stores the data that follows. Their byte format is in Casio's separate CZ-1 MIDI Specifications, which could not be read.
MIDI DISABLE appears if TONE DATA is DIS, MIDI is off or, for LOAD, PROTECT is ON. LOAD MIDI DATA ERROR points to mismatched channels, a cable, the other unit's settings or keys touched during transfer. After SAVE the OK message appears whether or not the data arrived. With a CZ-5000 (32 tones, E1-H8) or a CZ-1000/CZ-101 (16 tones, G1-H8) hold SUSTAIN while pressing YES; names, velocity and level are not transferred.
Source: Casio CZ-1 Operation Manual, Part 5 MIDI, viewer pp. 53-65
Backup battery. A built-in lithium battery keeps the internal memory; the manual gives it a life of about 5 years and warns that memory contents may be altered or lost when it weakens. Replacement is left to authorised service. Protect switch. With the rear PROTECT switch ON, nothing can be written. The manual says to leave it ON except for WRITE, EXCHANGE, SAVE and LOAD. Initialize. Switching on while holding INITIALIZE and then pressing YES resets the whole memory: the 64 internal tones return to the preset tones and the MIDI channels to 01. Noted by reviewers in 1986: the stereo chorus adds noise and there are no separate outputs for multitimbral parts.
These notes have not been checked against the sources yet. Corrections are welcome in the comments.
Sign in to write a comment.
Comments
0